English
Language : 

ISL54056 Datasheet, PDF (4/12 Pages) Intersil Corporation – Ultra Low ON-Resistance, +1.65V to +4.5V, Single Supply, Quad SPDT (Dual DPDT) Analog Switch
◁
ISL54056
Electrical Specifications - 4.3V Supply
Test Conditions: V+ = +3.9V to +4.5V, GND = 0V, VINH = 1.6V, VINL = 0.5V (Note 4),
unless otherwise specified (Continued)
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 7)
25
COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 7)
25
POWER SUPPLY CHARACTERISTICS
38
pF
102
pF
Power Supply Range
Full
1.65
4.5
V
Positive Supply Current, I+
V+ = +4.5V, VIN = 0V or V+
25
0.15
μA
Full
1.4
μA
Positive Supply Current, I+
V+ = +4.2V, VIN = 2.85V
DIGITAL INPUT CHARACTERISTICS
25
12
μA
Input Voltage Low, VINL
Full
0.5
V
Input Voltage High, VINH
Full
1.6
V
Input Current, IINH, IINL
V+ = 4.5V, VIN = 0V or V+
Full
-0.5
0.5
μA
NOTES:
4. VIN = input voltage to perform proper function.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
7. RON matching between channels is calculated by subtracting the channel with the highest max Ron value from the channel with lowest max Ron
value, between NC1 and NC2, NC3 and NC4 or between NO1 and NO2, NO3 and NO4.
Electrical Specifications - 3V Supply
Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V (Note 4),
unless otherwise specified
PARAMETER
TEST CONDITIONS
TEMP (NOTE 5)
(NOTE 5)
(°C)
MIN
TYP
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
Full
0
V+
V
ON Resistance, RON
V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+
25
(See Figure 5)
Full
0.45
0.55
Ω
0.65
Ω
RON Matching Between Channels, V+ = 2.7V, ICOM = 100mA, VNO or VNC = Voltage at
25
ΔRON
max RON (Note 7)
Full
0.05
0.12
Ω
0.15
Ω
RON Flatness, RFLAT(ON)
V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+
25
(Note 6)
Full
0.07
0.15
Ω
0.15
Ω
NO or NC OFF Leakage Current, V+ = 3.3V, VCOM = 0.3V, 3V, VNO or VNC = 3V, 0.3V
25
1.1
nA
INO(OFF) or INC(OFF)
Full
30
nA
COM ON Leakage Current,
V+ = 3.3V, VCOM = 0.3V, 3V, or VNO or VNC = 0.3V, 3V, 25
1.5
nA
ICOM(ON)
or Floating
Full
45
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF
25
34
ns
(See Figure 1)
Full
39
ns
Turn-OFF Time, tOFF
V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF
25
18
ns
(See Figure 1)
Full
23
ns
Break-Before-Make Time Delay, tD V+ = 3.3V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF Full
3
ns
(See Figure 3)
4
FN6357.1
October 30, 2006
 ▷