ISL71590SEH Datasheet, PDF (4/16 Pages) Intersil Corporation – Radiation Hardened

ISL71590SEH
Absolute Maximum Ratings
Maximum Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40V
In-Beam Maximum Supply Voltage (Note 5) . . . . . . . . . . . . . . . . . . . . . . 37V
Maximum Reverse Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40V
Maximum Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±40V
Case to Lead Breakdown Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±200V
ESD Rating
Human Body Model (Tested per MIL-STD-883 TM3015.7) . . . . . . . . 3kV
Machine Model (Tested per EIA/JESD22-A115-A) . . . . . . . . . . . . . . 300V
Charged Device Model (Tested per JESD22-C101D) . . . . . . . . . . . . 750V
Thermal Information
Thermal Resistance (Typical)
_JA (°C/W) _JC (°C/W)
2 Ld Flatpack (Notes 3, 4) . . . . . . . . . . . . . .
80
8
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +155°C
Maximum Junction Temperature (T_JMAX) . . . . . . . . . . . . . . . . . . . . .+150°C
Recommended Operating Conditions
Ambient Operating Temperature Range . . . . . . . . . . . . . .-55°C to +125°C
Maximum Operating Junction Temperature . . . . . . . . . . . . . . . . . .+150°C
Supply Voltage (V+ to V-) (Notes 5, 6) . . . . . . . . . . . . . . . . . . . . . . 4V to 33V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
3. _JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
4. For _JC, the “case temp” location is the center of the ceramic on the package underside.
5. The maximum supply voltage specified is for operation in a heavy ion environment at an LET = 86.4 MeV•cm²/mg.
6. The maximum voltage beyond which output current performance is not to be considered valid (Figure 9).
Electrical Specifications V_s = 5V, T_A = +25°C, unless otherwise noted. Boldface limits apply across the operating temperature range,
-55°C to +125°C.
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
MAX
(Note 7) TYP (Note 7) UNIT
V_S
Power Supply Voltage Range
I_O
Nominal Current Output
E
Ambient Error Accuracy
(V+ to V-) (Note 5)
4
31
V
298.1
µA
-0.50
-0.05
0.50
°C
TCI_O
Current Output Temperature Coefficient
E_A
Absolute Error without External Calibration Over full temperature range
NL
Nonlinearity
At 5 discrete temperature points
1
µA/K
-2.0
2.0
°C
-0.5
0.5
°C
RPT
Repeatability
After temperature range end point
-0.1
cycling
0.1
°C
dE/dt
Long Term Drift
V+ = 31V for 1khr at +125°C
-0.25
-0.05
0.25
°C
PSRR
Output Current V_S Rejection
V_nd
Voltage Noise Density
I_nd
Current Noise Density
Iso
Case Isolation to Either Lead
5V > V_S >4V
5V ≤ V_S ≤ 15V
5V ≤ V_S ≤ 31V
f = 100Hz
f = 100Hz
Case to lead voltage = 200V
0.05
0.03
0.04
0.03
30
10¹⁰
0.50
0.20
0.10
µA/V
µA/V
µA/V
µV/√Hz
pA/√Hz
Ω
C_S
Effective Shunt Capacitance
t_ON
Electrical Turn-On Time
I_LEAK
-10V Reverse Bias Leakage Current
POST RADIATION
f = 10Hz
V_S = 4V to I_OUT stable
+125°C = Worst case
65
pF
2
µs
50
nA
E-_RADD
Post Low Dose Rate Radiation (LDR)
Ambient error accuracy plus TID shift
-2.0
(Figure 19) Ambient Error 50krad at 0.01 rad(Si)/s
(Note 8)
0.5
°C
Post High Dose Rate Radiation (HDR)
Ambient error accuracy plus TID shift
-2.0
Ambient Error 300krad at 70 rad(Si)/s
(Note 8)
0.5
°C
NOTES:
7. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
8. The post radiation Ambient Error specs are defined as the absolute temperature error.
Submit Document Feedback
4
June 3, 2016
FN8376.2