ISL6236 Datasheet, PDF (4/35 Pages) Intersil Corporation – High-Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers

ISL6236
Electrical Specifications
No load on LDO, OUT1, OUT2, V_REF3, and REF, V_IN = 12V, EN2 = EN1 = VCC, VBYP = 5V, PVCC = 5V,
VEN_LDO = 5V, T_A = -40°C to +100°C, unless otherwise noted. Typical values are at T_A = +25°C. Boldface
limits apply over the operating temperature range, -40°C to +85°C. (Continued)
PARAMETER
CONDITIONS
MIN
MAX
(Note 6) TYP (Note 6) UNITS
Current-Limit Threshold
(Positive, Adjustable)
Zero-Current Threshold
GND - PHASE
V_ILIM = 0.5V
V_ILIM = 1V
V_ILIM = 2V
SKIP = GND, REF, or OPEN, GND - PHASE
40
50
60
mV
93
100
107
mV
185
200
215
mV
3
mV
Current-Limit Threshold (Negative, Default) SKIP = VCC, GND - PHASE
-120
mV
Soft-Start Ramp Time
Zero to full limit
1.7
ms
Operating Frequency
(V_tON = GND), SKIP = VCC
SMPS 1
SMPS 2
400
kHz
500
kHz
(V_tON = REF or OPEN),
SKIP = VCC
SMPS 1
SMPS 2
400
kHz
300
kHz
(V_tON = VCC), SKIP = VCC
SMPS 1
SMPS 2
200
kHz
300
kHz
ON-Time Pulse Width
Minimum OFF-Time
Maximum Duty Cycle
Ultrasonic SKIP Operating Frequency
V_tON = GND (400kHz/500kHz)
V_tON = REF or OPEN
(400kHz/300kHz)
V_tON = VCC (200kHz/300kHz)
T_A = -40°C to +100°C
T_A = -40°C to +85°C
V_tON = GND
V_tON = REF or OPEN
V_tON = VCC
SKIP = REF or OPEN
V_OUT1 = 5.00V
V_OUT2 = 3.33V
V_OUT1 = 5.05V
V_OUT2 = 3.33V
V_OUT1 = 5.05V
V_OUT2 = 3.33V
V_OUT1 = 5.05V
V_OUT2 = 3.33V
V_OUT1 = 5.05V
V_OUT2 = 3.33V
V_OUT1 = 5.05V
V_OUT2 = 3.33V
0.895 1.052 1.209
µs
0.475 0.555 0.635
µs
0.895 1.052 1.209
µs
0.833 0.925 1.017
µs
1.895 2.105 2.315
µs
0.833 0.925 1.017
µs
200
300
425
ns
200
300
410
ns
88
%
85
%
88
%
91
%
94
%
91
%
25
37
kHz
INTERNAL REGULATOR AND REFERENCE
LDO Output Voltage
BYP = GND, 5.5V < V_IN < 25V, LDOREFIN < 0.3V,
0 < ILDO < 100mA
4.925 5.000 5.075
V
LDO Output Voltage
BYP = GND, 5.5V < V_IN < 25V, LDOREFIN > (VCC -1V), 3.250 3.300 3.350
V
0 < ILDO < 100mA
LDO Output in Adjustable Mode
LDO Output Accuracy in Adjustable Mode
LDOREFIN Input Range
LDO Output Current
LDO Output Current During Switchover
LDO Output Current During Switchover
to 3.3V
V_IN = 5.5V to 25V, V_LDO = 2 x V_LDOREFIN
V_IN = 5.5V to 25V, V_LDOREFIN = 0.35V to 0.5V
V_IN = 5.5V to 25V, V_LDOREFIN = 0.5V to 2.25V
V_LDO = 2 x V_LDOREFIN
BYP = GND, V_IN = 5.5V to 25V (Note 5)
BYP = 5V, V_IN = 5.5V to 25V, LDOREFIN < 0.3V
BYP = 3.3V, V_IN = 5.5V to 25V, LDOREFIN > (VCC - 1V)
0.7
0.35
4.5
V
±2.5
%
±1.5
%
2.25
V
100
mA
200
mA
100
mA
LDO Short-Circuit Current
LDO = GND, BYP = GND
200
400
mA
4
FN6373.6
April 29, 2010