ISL43231_06 Datasheet, PDF (4/15 Pages) Intersil Corporation – Low-Voltage, Single and Dual Supply, Triple SPDT Analog Switch

ISL43231
Electrical Specifications ±5V SupplyTest Conditions: V_SUPPLY = ±4.5V to ±5.5V, GND = 0V, V_INH = 2.4V, V_INL = 0.8V (Note 3),
Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
TEMP (NOTE 4)
(NOTE 4)
(°C)
MIN
TYP
MAX UNITS
DYNAMIC CHARACTERISTICS
Enable Turn-ON Time, t_ON
V_S = ±4.5V, V_NO or V_NC = ±3V, R_L =300Ω, C_L = 35pF, 25
-
V_IN = 0 to 3 (See Figure 1)
Full
-
35
50
ns
-
60
ns
Enable Turn-OFF Time, t_OFF
V_S = ±4.5V, V_NO or V_NC = ±3V, R_L =300Ω, C_L = 35pF, 25
-
V_IN = 0 to 3 (See Figure 1)
Full
-
22
35
ns
-
40
ns
Address Transition Time, t_TRANS V_S = ±4.5V, V_NO or V_NC = ±3V, R_L =300Ω, C_L = 35pF, 25
-
V_IN = 0 to 3 (See Figure 1)
Full
-
43
60
ns
-
70
ns
Break-Before-Make Time, t_BBM
V_S = ±5.5V, V_NO or V_NC = 3V, R_L = 300Ω, C_L = 35pF, Full
2
7
V_IN = 0 to 3V (See Figure 3)
Latch Setup Time, t_S
(See Figure 4)
25
25
-
Full
35
-
-
ns
-
ns
-
ns
Latch Hold Time, t_H
(See Figure 4)
25
0
-
-
ns
Full
0
-
-
ns
Latch Pulse Width, t_WPW
(See Figure 4)
25
15
-
Full
25
-
-
ns
-
ns
Charge Injection, Q
C_L = 1.0nF, V_G = 0V, R_G = 0Ω (See Figure 2)
25
NO/NC OFF Capacitance, C_OFF f = 1MHz, V_NO or V_NC = V_COM = 0V (See Figure 8)
25
COM OFF Capacitance, C_OFF
f = 1MHz, V_NO or V_NC = V_COM = 0V (See Figure 8)
25
COM ON Capacitance, C_COM(ON) f = 1MHz, V_NO or V_NC = V_COM = 0V (See Figure 8)
25
OFF Isolation
Crosstalk (Note 8)
R_L = 50Ω, C_L = 15pF, f = 100kHz,
25
V_NOx or V_NCx = 1V_RMS (See Figures 5, 7 and 20)
25
-
0.3
1
pC
-
3
-
pF
-
9
-
pF
-
14
-
pF
-
92
-
dB
-
<-110
-
dB
All Hostile Crosstalk (Note 8)
25
-
-105
1.5
dB
POWER SUPPLY CHARACTERISTICS
Power Supply Range
Full
±2
-
±6
V
Positive Supply Current, I+
V_S = ±5.5V, V_INH, V_ADD = 0V or V+, Switch On or Off Full
-7
-
7
µA
Negative Supply Current, I-
Full
-1
-
1
µA
NOTES:
3. V_IN = Input logic voltage to configure the device in a given state.
4. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
5. ∆R_ON = R_ON (MAX) - R_ON (MIN).
6. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
7. Leakage parameter is 100% tested at high temp, and guaranteed by correlation at 25°C.
8. Between any two switches.
Electrical Specifications +12V Supply
PARAMETER
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V_ANALOG
Test Conditions: V+ = +10.8V to +13.2V, GND = 0V, V_INH = 4V, V_INL = 0.8V (Note 3),
Unless Otherwise Specified
TEST CONDITIONS
TEMP (NOTE 4)
(°C)
MIN
(NOTE 4)
TYP
MAX UNITS
Full
0
-
V+
V
4
FN6054.2
February 27, 2006