X95840 Datasheet, PDF (3/13 Pages) Intersil Corporation – Quad Digital Controlled Potentiometers

X95840
Absolute Maximum Ratings
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage at any digital interface pin
with respect to GND . . . . . . . . . . . . . . . . . . . . . . -0.3V to V_CC+0.3
V_CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6V
Voltage at any DCP pin with respect to GND. . . . . . . . -0.3V to V_CC
Lead temperature (soldering, 10s). . . . . . . . . . . . . . . . . . . . . . 300°C
I_W (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
Recommended Operating Conditions
Temperature Range (Industrial) . . . . . . . . . . . . . . . . . . -40°C to 85°C
V_CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Power rating of each DCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5mW
Wiper current of each DCP . . . . . . . . . . . . . . . . . . . . . . . . . . ±3.0mA
CAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional
operation of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Analog Specifications Over recommended operating conditions unless otherwise stated.
SYMBOL
PARAMETER
TEST CONDITIONS
TYP
MIN (Note 1) MAX
UNIT
R_TOTAL R_H to R_L resistance
W, U versions respectively
R_H to R_L resistance tolerance
R_W
Wiper resistance
V_CC = 3.3V @ 25°C
Wiper current = V_CC / R_TOTAL
C_H/C_L/C_W Potentiometer Capacitance (Note 15)
I_LkgDCP Leakage on DCP pins (Note 15)
Voltage at pin from GND to V_CC
VOLTAGE DIVIDER MODE (0V @ RL_i; V_CC @ RH_i; measured at RW_i, unloaded; i = 0, 1, 2, or 3)
INL (Note 6) Integral non-linearity
10, 50
kΩ
-20
+20
%
70
200
Ω
10/10/25
pF
0.1
1
µA
-1
1
LSB
(Note 2)
DNL (Note 5) Differential non-linearity
Monotonic over all tap positions
-0.5
0.5
LSB
(Note 2)
ZSerror Zero-scale error
(Note 3)
U option
W option
0
1
7
LSB
(Note 2)
0
0.5
2
FSerror Full-scale error
(Note 4)
U option
W option
-7
-1
-2
-1
0
LSB
(Note 2)
0
V_MATCH DCP to DCP matching
(Note 7)
Any two DCPs at same tap position, same
-2
voltage at all RH terminals, and same voltage
at all RL terminals
2
LSB
(Note 2)
TC_V (Note 8) Ratiometric Temperature Coefficient DCP Register set to 80 hex
±4
ppm/°C
RESISTOR MODE (Measurements between RW_i and RL_i with RH_i not connected, or between RW_i and RH_i with RL_i not connected. i = 0, 1, 2 or 3)
RINL
Intregal non-linearity
(Note 12)
DCP register set between 20 hex and
-1
FF hex. Monotonic over all tap positions
1
MI
(Note 9)
RDNL Differential non-linearity
(Note 11)
-0.5
0.5
MI
(Note 9)
Roffset Offset
(Note 10)
U option
0
1
7
MI
(Note 9)
W option
0
0.5
2
MI
(Note 9)
R_MATCH DCP to DCP Matching
(Note 13)
Any two DCPs at the same tap position with
-2
the same terminal voltages.
2
MI
(Note 9)
TC_R
Resistance Temperature Coefficient DCP register set between 20 hex and FF hex
±45
(Note 14)
ppm/°C
3
FN8213.1
September 27, 2005