DG401 Datasheet, PDF (3/9 Pages) Intersil Corporation – Monolithic CMOS Analog Switches

DG401, DG403, DG405
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0V
GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V
V_L. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (GND - 0.3V) to (V+) +0.3V
Digital Inputs V_S, V_D (Note 1) . . . . . (V-) -2V to (V+) + 2V or 30mA,
Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle, Max) . . 100mA
Thermal Information
Thermal Resistance (Typical, Note 2)
θ_JA (^oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
115
Maximum Junction Temperature (Plastic Package) . . . . . . . . .150^oC
Maximum Storage Temperature Range . . . . . . . . . . . . .-65^oC to 150^oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300^oC
(SOIC - Lead Tips Only)
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40^oC to 85^oC
Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V (Max)
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V (Max)
Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V (Min)
Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤20ns
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Signals on S_X, D_X, or IN_X exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
2. θ_JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, V_IN = 2.4V, 0.8V (Note 3), V_L = 5V,
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
DYNAMIC CHARACTERISTICS
Turn-ON Time, t_ON
Turn-OFF Time, t_OFF
Break-Before-Make Time Delay (DG403), t_D
Charge Injection, Q (Figure 3)
OFF Isolation (Figure 4)
Crosstalk (Channel-to-Channel) (Figure 6)
R_L = 300Ω, C_L = 35pF
R_L = 300Ω, C_L = 35pF
C_L = 10nF, V_G = 0V, R_G = 0Ω
R_L = 100Ω, C_L = 5pF, f = 1MHz
Source OFF Capacitance, C_S(OFF)
Drain OFF Capacitance, C_D(OFF)
Channel ON Capacitance, C_D(ON) + C_S(ON)
DIGITAL INPUT CHARACTERISTICS
f = 1MHz, V_S = V_D = 0V (Figure 7)
Input Current with V_IN Low, I_IL
Input Current with V_IN High, I_IH
ANALOG SWITCH CHARACTERISTICS
V_IN Under Test = 0.8V, All Others = 2.4V
V_IN Under Test = 2.4V, All Others = 0.8V
Analog Signal Range, V_ANALOG
Drain-Source ON Resistance, r_DS(ON)
V+ = 13.5V, V- = -13.5V,
I_S = 10mA, V_D = ±10V
r_DS(ON) Matching Between Channels, ∆r_DS(ON) V+ = 16.5V, V- = -16.5V,
I_S = -10mA, V_D = 5, 0, -5V
Source OFF Leakage Current, I_S(OFF)
V+ = 16.5V, V- = -16.5
V_D = ±15.5V, V_S = 15.5V
Drain OFF Leakage Current, I_D(OFF)
Channel ON Leakage Current, I_D(ON) + I_S(ON) V± = ±16.5V, V_D = V_S = ±15.5V
TEMP
(^oC)
25
25
25
25
25
25
25
25
25
Full
Full
Full
25
Full
25
Full
25
Full
25
Full
25
Full
(NOTE 4) (NOTE 5) (NOTE 4)
MIN
TYP
MAX UNITS
-
100
150
ns
-
60
100
ns
5
12
-
ns
-
60
-
pC
-
72
-
dB
-
-90
-
dB
-
12
-
pF
-
12
-
pF
-
39
-
pF
-1
0.005
1
µA
-1
0.005
1
µA
-15
-
15
V
-
20
45
Ω
-
-
55
Ω
-
3
3
Ω
-
-
5
Ω
-0.5
-0.01
0.5
nA
-5
-
5
nA
-0.5
-0.01
0.5
nA
-5
-
5
nA
-1
-0.04
1
nA
-10
-
10
nA
3