DG201 Datasheet, PDF (3/7 Pages) Intersil Corporation – CMOS Quad SPST Analog Switch

DG201
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36V
V+ to V_D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30V
V_D to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30V
V_D to V_S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28V
V_REF to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33V
V_REF to V_IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30V
V_REF to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V
V_IN to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V
Current (Any Terminal). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30mA
Thermal Information
Thermal Resistance (Typical, Note 1)
θ_JA (^oC/W) θ_JC (^oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . .
90
N/A
Maximum Junction Temperature
Plastic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150^oC
Maximum Storage Temperature Range . . . . . . . . . . -65^oC to 150^oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300^oC
Operating Conditions
Temperature Range
“C” Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0^oC to 70^oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θ_JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications T_A = 25^oC, V+ = +15V, V- = -15V
“C” SUFFIX
PARAMETER
TEST CONDITIONS
(NOTE 2)
0^oC
25^oC
70^oC
UNITS
DYNAMIC CHARACTERISTICS
Turn-ON Time (Note 3), t_ON
Turn-OFF Time (Note 3), t_OFF
Charge Injection, Q
R_L = 1kΩ, V_ANALOG = -10V to +10V (Figure 1)
-
1.0
-
µs
R_L = 1kΩ, V_ANALOG = -10V to +10V (Figure 1)
-
0.5
-
µs
Figure 2
-
20 (Typ)
-
mV
Off Isolation Rejection Ratio, OIRR
Crosstalk (Channel-to-Channel), CCRR
f = 1MHz, R_L = 100Ω, C_L ≤ 5pF, (Figure 3)
One Channel Off
-
50 (Typ)
-
dB
-
-50 (Typ)
-
dB
DIGITAL INPUT CHARACTERISTICS
Input Logic Current, I_IN(ON)
Input Logic Current, I_N(OFF)
ANALOG SWITCH CHARACTERISTICS
V_IN = 0.8V (Note 3)
V_IN = 2.4V (Note 3)
±1
±1
±10
µA
±1
±1
±10
µA
Analog Signal Range, V_ANALOG
Drain-Source ON Resistance, r_DS(ON)
Channel-to-Channel
r_DS(ON) Match, r_DS(ON)
Drain OFF Leakage Current, I_D(OFF)
Source OFF Leakage Current, I_S(OFF)
Channel ON Leakage
Current, I_D(ON) + I_S(ON)
POWER SUPPLY CHARACTERISTICS
I_S = 10mA, V_ANALOG = ±10V
V_ANALOG = -14V to +14V
V_ANALOG = -14V to +14V
V_D = V_S = -14V to +14V
-
±15 (Typ)
-
V
100
100
125
Ω
-
30 (Typ)
-
Ω
-
±5
100
nA
-
±5
100
nA
-
±5
200
nA
Supply Current, I+ Positive
Supply Current, I- Negative
V_IN = 0V or V_IN = 5V
2000
1000
2000
µA
2000
1000
2000
µA
NOTES:
2. Typical values are for design aid only, not guaranteed and not subject to production testing.
3. All channels are turned off by high “1” logic inputs and all channels are turned on by low “0” inputs; however 0.8V to 2.4V describes the minimum
range for switching properly. Peak input current required for transition is typically -120µA.
3