X9259 Datasheet, PDF (13/21 Pages) Xicor Inc. – Quad Digitally-Controlled (XDCP) Potentiometers

X9259
Absolute Maximum Ratings
Temperature under bias . . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage on SCL, SDA, any address input, V_CC
with respect to V_SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1V to +7V
∆V = | (V_H–V_L) | . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
Lead temperature (soldering, 10 seconds) . . . . . . . . . . . . . . . 300°C
I_W (10 seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
Recommended Operating Conditions
Temperature (Commercial) . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Temperature (Industrial). . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage (V_CC) (Note 4) Limits
X9259. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V ± 10%
X9259-2.7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
CAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; the functional
operation of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
Analog Specifications Over recommended industrial (2.7V) operating conditions unless otherwise stated.
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
R_TOTAL
R_TOTAL
I_W
R_W
End to End Resistance
End to End Resistance
End to End Resistance Tolerance
Power Rating
Wiper Current
Wiper Resistance
T version
U version
25°C, each pot
I_W =
V(V_CC)
R_TOTAL
@ V_CC = 3V
100
50
±20
50
±3
300
I_W =
V(V_CC)
R_TOTAL
@ V_CC = 5V
150
V_TERM
Voltage on any R_H or R_L Pin
Noise
Resolution
Absolute Linearity ⁽¹⁾
V_SS = 0V
Ref: 1V
R_w(n)(actual) - R_{w(n)(expected)(5)}
V_SS
-120
0.4
-1
V_CC
+1
Relative Linearity ⁽²⁾
R_{w(n + 1)} - [R_{w(n) + MI}]⁽⁵⁾
-0.6
+0.6
UNITS
kΩ
kΩ
%
mW
mA
Ω
Ω
V
dB/√Hz
%
MI⁽³⁾
MI⁽³⁾
C_H/C_L/C_W
Temperature Coefficient of R_TOTAL
Ratiometric Temp. Coefficient
Potentiometer Capacitances
See Macro model
±300
-20
+20
10/10/25
ppm/°C
ppm/°C
pF
Notes: (1) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a
potentiometer.
(2) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a
potentiometer. It is a measure of the error in step size.
(3) MI = RTOT / 255 or (R_H – R_L) / 255, single pot
(4) During power up V_CC > V_H, V_L, and V_W.
(5) n = 0, 1, 2, …,255; m =0, 1, 2, …, 254.
13
FN8169.2
September 16, 2005