ISL6336 Datasheet, PDF (12/31 Pages) Intersil Corporation – 6-Phase PWM Controller with Light Load Efficiency Enhancement and Current Monitoring

ISL6336, ISL6336A
IL1 + IL2 + IL3, 7A/DIV
IL3, 7A/DIV
PWM3, 5V/DIV
IL2, 7A/DIV
IL1, 7A/DIV
PWM2, 5V/DIV
PWM1, 5V/DIV
1µs/DIV
FIGURE 1. PWM AND INDUCTOR-CURRENT WAVEFORMS
FOR 3-PHASE CONVERTER
INPUT-CAPACITOR CURRENT
CHANNEL 3
INPUT
CHANNEL 2
INPUT
CHANNEL 1
INPUT
1µs/DIV
FIGURE 2. CHANNEL INPUT CURRENTS AND INPUT
CAPACITOR RMS CURRENT FOR 3-PHASE
CONVERTER
The output capacitors conduct the ripple component of the
inductor current. In the case of multiphase converters, the
capacitor current is the sum of the ripple currents from each of
the individual channels. Compare Equation 1 to the expression
for the peak-to-peak current after the summation of N
symmetrically phase-shifted inductor currents in Equation 2.
Peak-to-peak ripple current decreases by an amount
proportional to the number of channels. Output-voltage ripple is
a function of capacitance, capacitor equivalent series
resistance (ESR), and inductor ripple current. Reducing the
inductor ripple current allows the designer to use fewer or less
costly output capacitors.
I_{C, PP}=
(_{---V----I--N-----}–_-----(_--N------⋅_{----V-----O----U----T----})_--)_----⋅_{----V----O----U-----T-}
L ⋅ f_S ⋅ V_IN
(EQ. 2)
Another benefit of interleaving is to reduce the input ripple
current. The input capacitance is determined in part by the
maximum input ripple current. Multiphase topologies can
improve the overall system cost and size by lowering the
input ripple current and allowing the designer to reduce the
cost of input capacitance. The example in Figure 2 illustrates
the input currents from a three-phase converter combining to
reduce the total input ripple current.
The converter depicted in Figure 2 delivers 36A to a 1.5V load
from a 12V input. The RMS input capacitor current is 5.9A.
Compare this to a single-phase converter also stepping down
12V to 1.5V at 36A. The single-phase converter has 11.9A_RMS
input capacitor current. The single-phase converter must use
an input capacitor bank with twice the RMS current capacity as
the equivalent three-phase converter.
Figures 21, 22 and 23 in the section entitled “Input Capacitor
Selection” on page 29 can be used to determine the input
capacitor RMS current based on the load current, the duty
cycle, and the number of channels. They are provided as
aids in determining the optimal input capacitor solution.
Figure 24 shows the single phase input-capacitor RMS
current for comparison.
PWM Modulation Scheme
The ISL6336, ISL6336A adopts Intersil's proprietary Active
Pulse Positioning (APP) modulation scheme to improve the
transient performance. APP control is a unique dual-edge
PWM modulation scheme with both PWM leading and
trailing edges being independently moved to provide the
best response to the transient loads. The PWM frequency,
however, is constant and set by the external resistor
between the FS pin and GND.
To further improve the transient response, the ISL6336,
ISL6336A also implements Intersil's proprietary Adaptive
Phase Alignment (APA) technique. The APA, with sufficiently
large load step currents, can turn on all phases simultaneously.
With both APP and APA control, ISL6336, ISL6336A can
achieve excellent transient performance and reduce the
demand on the output capacitors.
Under steady state conditions the operation of the ISL6336,
ISL6336A PWM modulator appears to be that of a conventional
trailing edge modulator. Conventional analysis and design
methods can therefore be used for steady state and small
signal operation.
PWM and PSI# Operation
The timing of each converter is set by the number of active
channels. The default channel setting for the ISL6336,
ISL6336A is six. The switching cycle is defined as the time
between PWM pulse termination signals of each channel.
The cycle time of the pulse termination signal is the inverse
of the switching frequency set by the resistor between the
FS pin and ground. The PWM signals command the
MOSFET drivers to turn on/off the channel MOSFETs.
In the default 6-phase operation, the PWM2 pulse happens
1/6 of a cycle after PWM1, the PWM3 pulse happens 1/6 of
a cycle after PWM2, etc.
The ISL6336, ISL6336A works in a 1- to 6-phase configuration.
Connecting the PWM6 pin to VCC selects 5-phase operation
and the pulse times are spaced in 1/5 cycle increments.
12
FN6504.1
May 28, 2009