ISL6556A Datasheet, PDF (11/24 Pages) Intersil Corporation – Optimized Multi-Phase PWM Controller with 6-Bit DAC for VR10.X Application

ISL6556A
converter has 11.9A RMS input capacitor current. The
single-phase converter must use an input capacitor bank
with twice the RMS current capacity as the equivalent three-
phase converter.
INPUT-CAPACITOR CURRENT, 10A/DIV
CHhaAnNnNeEl 3L 3
iINnpPuUtTcCurUreRnRtENT
10A/DIV
CHANNEL 2
INPUT CURRENT
10A/DIV
CHANNEL 1
INPUT CURRENT
10A/DIV
1µs/DIV
FIGURE 2. CHANNEL INPUT CURRENTS AND INPUT-
CAPACITOR RMS CURRENT FOR 3-PHASE
CONVERTER
Figures 14, 15 and 16 in the section entitled Input Capacitor
Selection can be used to determine the input-capacitor RMS
current based on load current, duty cycle, and the number of
channels. They are provided as aids in determining the
optimal input capacitor solution. Figure 17 shows the single
phase input-capacitor RMS current for comparison.
PWM Operation
The timing of each converter leg is set by the number of
active channels. The default channel setting for the
ISL6556A is four. One switching cycle is defined as the time
between PWM1 pulse termination signals. The pulse
termination signal is the internally generated clock signal
that triggers the falling edge of PWM1. The cycle time of the
pulse termination signal is the inverse of the switching
frequency set by the resistor between the FS pin and
ground. Each cycle begins when the clock signal commands
the channel-1 PWM output to go low. The PWM1 transition
signals the channel-1 MOSFET driver to turn off the channel-1
upper MOSFET and turn on the channel-1 synchronous
MOSFET. In the default channel configuration, the PWM2
pulse terminates 1/4 of a cycle after PWM1. The PWM3
output follows another 1/4 of a cycle after PWM2. PWM4
terminates another 1/4 of a cycle after PWM3.
If PWM3 is connected to VCC, two channel operation is
selected and the PWM2 pulse terminates 1/2 of a cycle later.
Connecting PWM4 to VCC selects three channel operation
and the pulse-termination times are spaced in 1/3 cycle
increments.
Once a PWM signal transitions low, it is held low for a
minimum of 1/3 cycle. This forced off time is required to
ensure an accurate current sample. Current sensing is
described in the next section. After the forced off time
expires, the PWM output is enabled. The PWM output state
is driven by the position of the error amplifier output signal,
V_COMP, minus the current correction signal relative to the
sawtooth ramp as illustrated in Figure 4. When the modified
V_COMP voltage crosses the sawtooth ramp, the PWM output
transitions high. The MOSFET driver detects the change in
state of the PWM signal, turns off the synchronous MOSFET
and turns on the upper MOSFET. The PWM signal remains
high until the pulse termination signal commands the
beginning of the next cycle by triggering the PWM signal low.
Current Sensing
During the forced off time following a PWM transition low, the
controller senses channel current by sampling the voltage
across the lower MOSFET r_DS(ON) (see Figure 3). A ground-
referenced operational amplifier, internal to the ISL6556A, is
connected to the PHASE node through a resistor, R_ISEN. The
voltage across R_ISEN is equivalent to the voltage drop across
the r_DS(ON) of the lower MOSFET while it is conducting. The
resulting current into the ISEN pin is proportional to the
channel current, I_L. The ISEN current is sampled and held
after sufficient settling time every switching cycle. The
sampled current, I_n, is used for channel-current balance, load-
line regulation, overcurrent protection, and module current
sharing. From Figure 3, the following equation for I_n is derived
I_n
=
I_L
r---_{D----S----(--O----N-----)}
R_ISEN
(EQ. 3)
where I_L is the channel current.
If r_DS(ON) sensing is not desired, an independent current-
sense resistor in series with the lower MOSFET source can
serve as a sense element. The circuitry shown in Figure 3
represents channel n of an N-channel converter. This
circuitry is repeated for each channel in the converter, but
may not be active depending upon the status of the PWM3
and PWM4 pins as described under PWM Operation
section.
I_n
ISEN
=
IL
-r--D-----S----⁽---O-----N-----⁾
RISEN
SAMPLE
&
HOLD
-
+
V_IN
CHANNEL N
UPPER MOSFET
I_L
ISEN(n)
R_ISEN
-
IL rDS_(ON)
+
CHANNEL N
LOWER MOSFET
ISL6556A INTERNAL CIRCUIT EXTERNAL CIRCUIT
FIGURE 3. INTERNAL AND EXTERNAL CURRENT-SENSING
CIRCUITRY
11