ISL6269B_14 Datasheet, PDF (10/16 Pages) Intersil Corporation – High-Performance Notebook PWM Controller With Audio-Frequency Clamp

ISL6269B
MOSFET Gate-Drive Outputs LG and UG
The ISL6269B has internal gate-drivers for the high-side and
low-side N-Channel MOSFETs. The LG gate-driver is optimized for
low duty-cycle applications where the low-side MOSFET
conduction losses are dominant, requiring a low r_DS(ON) MOSFET.
The LG pull-down resistance is small in order to clamp the gate of
the MOSFET below the V_GS(th) at turnoff. The current transient
through the gate at turnoff can be considerable because the
switching charge of a low r_DS(ON) MOSFET can be large. Adaptive
shoot-through protection prevents a gate-driver output from
turning on until the opposite gate-driver output has fallen below
approximately 1V. The dead-time shown in Figure 3 is extended
by the additional period that the falling gate voltage stays above
the 1V threshold. The high-side gate-driver output voltage is
measured across the UG and PHASE pins while the low-side
gate-driver output voltage is measured across the LG and PGND
pins. The power for the LG gate-driver is sourced directly from the
PVCC pin. The power for the UG gate-driver is sourced from a
“boot” capacitor connected across the BOOT and PHASE pins.
The boot capacitor is charged from a 5V bias supply through a
“boot diode” each time the low-side MOSFET turns on, pulling the
PHASE pin low. The ISL6269B has an integrated boot diode
connected from the PVCC pin to the BOOT pin.
t_LGFUGR
50%
UG
LG
50%
t_UGFLGR
FIGURE 3. LG AND UG DEAD-TIME
Diode Emulation
The ISL6269B normally operates in Continuous Conduction
Mode (CCM), minimizing conduction losses by forcing the low-
side MOSFET to operate as a synchronous rectifier. An
improvement in light-load efficiency is achieved by allowing the
converter to operate in Diode Emulation Mode (DEM), where the
low-side MOSFET behaves as a smart-diode, forcing the device to
block negative inductor current flow. The ISL6269B can be
configured to operate in DEM by setting the FCCM pin low.
Setting the FCCM pin high will disable DEM.
Positive-going inductor current flows from either the source of
the high-side MOSFET, or the drain of the low-side MOSFET.
Negative-going inductor current usually flows into the drain of the
low-side MOSFET. When the low-side MOSFET conducts positive
inductor current, the phase voltage will be negative with respect
to the GND and PGND pins. Conversely, when the low-side
MOSFET conducts negative inductor current, the phase voltage
will be positive with respect to the GND and PGND pins. Negative
inductor current occurs when the output load current is less than
½ the inductor ripple current. Sinking negative inductor current
through the low-side MOSFET lowers efficiency through
unnecessary conduction losses. Efficiency can be further
improved with a reduction of unnecessary switching losses by
reducing the PWM frequency. It is characteristic of the R3™
architecture for the PWM frequency to decrease while in diode
emulation. The extent of the frequency reduction is proportional
to the reduction of load current. Upon entering DEM, the PWM
frequency makes an initial step-reduction because of a 33%
step-increase of the window voltage V_W. The ISL6269B features
an audio filter that clamps the minimum PWM frequency to a
level beyond human hearing when the output load current
becomes low enough.
With FCCM pulled low, the converter will automatically enter DEM
after the PHASE pin has detected positive voltage, while the LG
gate-driver pin is high for eight consecutive PWM pulses. The
converter will return to CCM on the following cycle after the
PHASE pin detects negative voltage, indicating that the body
diode of the low-side MOSFET is conducting positive inductor
current.
Overcurrent and Short-Circuit Protection
The overcurrent protection (OCP) and short circuit protection
(SCP) setpoint is programmed with resistor R_SEN that is
connected across the ISEN and PHASE pins. The PHASE pin is
connected to the drain terminal of the low-side MOSFET.
The SCP setpoint is internally set to twice the OCP setpoint. When
an OCP or SCP fault is detected, the PGOOD pin will pull down to
30Ω and latch off the converter. The fault will remain latched
until the EN pin has been pulled below the falling EN threshold
voltage V_ENTHF or if ^V_VCC has decayed below the falling POR
threshold voltage ^V_{VCC_THF}.
The OCP circuit does not directly detect the DC load current
leaving the converter. The OCP circuit detects the peak of
positive-flowing output inductor current. The low-side MOSFET
drain current I_D is assumed to be equal to the positive output
inductor current when the high-side MOSFET is off. The inductor
current develops a negative voltage across the r_DS(ON) of the
low-side MOSFET that is measured shortly after the LG gate
driver output goes high. The ISEN pin sources the OCP sense
current I_SEN, through the OCP programming resistor R_SEN,
forcing the ISEN pin to zero volts with respect to the GND pin. The
negative voltage across the PHASE and GND pins is nulled by the
voltage dropped across R_SEN as I_SEN conducts through it. An OCP
fault occurs if I_SEN rises above the OCP threshold current I_OC
while attempting to null the negative voltage across the PHASE
and GND pins. The I_SEN must exceed I_OC on all the PWM pulses
that occur within 20µs. If I_SEN falls below I_OC on a PWM pulse
before 20µs has elapsed, the timer will be reset. An SCP fault will
occur within 10µs when I_SEN exceeds twice I_OC. The relationship
between I_D and I_SEN is written as:
I_SEN  R_SEN = I_D  r_{DSON}
(EQ. 3)
Submit Document Feedback ₁₀
FN6280.3
November 17, 2014