HR150 Datasheet, PDF (1/7 Pages) Interpoint Corporation Company – -40°C to +85°C operation Transient protection 50 V for 50 ms

DC/DC Converters
28 Volt Input
NOT RECOMMENDED FOR NEW DESIGNS
hr150
Series
20 Watt
Features
• -40°C to +85°C operation
• 18 to 36 VDC input
• Transient protection 50 V for 50 ms
for 28 Vin models
• Fully isolated
• Fixed frequency switching
• Output trim on single output models
• Inhibit function
• Indefinite short circuit protection
• Up to 86% efficiency
models
VDC Output
single
5
12
15
Dual
±12
±15
triple
+5 & ±12
+5 & ±15
Size (max.): HR151 and HR152 models, case H6

2.110 x 1.1120 x 0.495 inches (53.59 x 28.45 x 12.57 mm)
HR153 models, case F4

1.950 x 1.350 x 0.505 inches (49.53 x 34.29 x 12.83 mm)
See cases F4 and H6 for dimensions.
Weight: HR151 and HR152: 50 grams typical. HR153: 53 grams typical.
Screening: Standard only. See screening table for more information.
description
The HR150 Series™ DC/DC converters have been designed to give
industrial applications the same high reliability, small size, and high
performance that Interpoint has provided to military and aerospace
programs since 1969.
models and 250 kHz typical for triple output models. They achieve
high isolation (500 V, 100 megohm) through use of a transformer in
the forward power circuit and an opto-coupler in the feedback control
loop.
High Reliability
Each HR150 converter is built to perform reliably in the harshest
environments. Assembled using thick-film hybrid technology, HR150
converters have more uniform thermal coefficients and 50% fewer
connections than converters built by surface mount techniques. The
HR150 converter parts use the same manufacturing procedures and
quality controls that we apply to converters designed for commercial
airliners, the space shuttle, advanced fighter aircraft, and other high
reliability applications. The steel cases are hermetically sealed in a
dry nitrogen environment and are guaranteed a maximum leak rate
of less than 10^-3 atm-cc/sec. All devices are 100% electrically tested.
Small Size – Low Profile
The HR150 Series manufacturing techniques provide extremely small
size and low profile components. Each converter uses less than 2.7
square inches of board area. The overall power density is from 11 to
17 watts per cubic inch.
High Performance
The HR150 Series converters are high efficiency, low noise, pulse
width modulated, forward mode switching regulators with a constant
switching frequency of 125 kHz typical for single and dual output
HR 150 Series input voltage range is 18 to 36 VDC. Outputs are
available as 5, 12, 15, ±12, ±15, +5/±12, and +5/±15 VDC. The
converters typically provide greater than 80% efficiency over the
entire input range and from 25% to full load. Line regulation is typi-
cally within 0.1 % and load regulation within 0.2%.
HR150 converters are designed to operate between -40°C and
+85°C case and are short circuit protected up to a case temperature
of 85°C. The combination of high conversion efficiency and heat
dissipating metal enclosures minimizes heat sinking requirements.
If additional dissipation is desired, heat conducting material (PCB,
copper sheet, heat sink, etc.) may be brought into contact with the
unit’s baseplate.
An inhibit function is provided for HR150 converters when the inhibit
input pin is connected to the input common. The open circuit voltage
of the inhibit input pin is 11 to 13 VDC. The inhibit input pin must
sink approximately 1 mA during the inhibit state. During inhibit, the
converter’s output voltage drops to less than 1 volt and the input
current is typically 8 mA.
Crane Aerospace & Electronics
Electronics Group (Interpoint Brand)
PO Box 97005•Redmond WA 98073-9705
425.882.3100 • [e-mail]
www.interpoint.com
Page ­1­­ of 7
HR150 Rev E 20100212