V23815-U1306-MXXX Datasheet, PDF (7/9 Pages) Infineon Technologies AG – Parallel Optical Link: PAROLI T X AC, 1.6 Gbit/s

Pin#
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
Pin Name
V_EE
V_EE
t.b.l.o.
DO04P
DO04N
V_EE
DO05P
DO05N
V_EE
V_EE
DO06P
DO06N
V_EE
V_EE
DO07P
DO07N
V_EE
V_EE
DO08P
DO08N
V_EE
V_EE
V_EE
DO09P
DO09N
t.b.l.o.
V_EE
V_EE
DO10P
DO10N
V_EE
V_EE
DO11P
DO11N
V_EE
V_EE
DO12P
DO12N
V_EE
V_EE
V_EE
t.b.l.o.
V_EE
V_CC3
Level/Logic Description
Ground
Ground
to be left open
LVDS Out Data Output #4, non-inverted
LVDS Out Data Output #4, inverted
Ground
LVDS Out Data Output #5, non-inverted
LVDS Out Data Output #5, inverted
Ground
Ground
LVDS Out Data Output #6, non-inverted
LVDS Out Data Output #6, inverted
Ground
Ground
LVDS Out Data Output #7, non-inverted
LVDS Out Data Output #7, inverted
Ground
Ground
LVDS Out Data Output #8, non-inverted
LVDS Out Data Output #8, inverted
Ground
Ground
Ground
LVDS Out Data Output #9, non-inverted
LVDS Out Data Output #9, inverted
to be left open
Ground
Ground
LVDS Out Data Output #10, non-inverted
LVDS Out Data Output #10, inverted
Ground
Ground
LVDS Out Data Output #11, non-inverted
LVDS Out Data Output #11, inverted
Ground
Ground
LVDS Out Data Output #12, non-inverted
LVDS Out Data Output #12, inverted
Ground
Ground
Ground
to be left open
Ground
Power supply voltage of digital
circuitry
Pin#
67
68
69
70
71
72
Pin Name Level/Logic Description
-SD12
LVCMOS
Out
low active
Signal Detect on fiber #12
Low=signal of sufficient AC
power is present on fiber #12
High=signal on fiber #12 is
insufficient
ENSD
LVCMOS In
High=SD1 and SD12 function
enabled
Low=SD1 and SD12 are set to
permanent active.Internal pull-
up pulls to high level when in-
put is left open.
t.b.l.o.
to be left open
V_CC2
Power supply voltage of LVDS
outputs
V_CC1
Power supply voltage of ampli-
fier
V_EE
Ground
Optical Port
Designed for Infineon Simplex MT Connector (SMC)
• Port outside dimensions: 15.4 mm x 6.8 mm (width x height)
• MT compatible fiber spacing (250 µm) and alignment pin
spacing (4600 µm)
• Alignment pins fixed in module port
• Integrated mechanical keying
• process plug (SMC dimensions) included with every module
• cleaning of port and connector interfaces necessary prior
to mating
Features of Infineon Simplex MT Connector (SMC)
(as part of optional PAROLI fiber optic cables)
• Uses standardized MT ferrule
• MT compatible fiber spacing (250 µm) and alignment pin
spacing (4600 µm)
• Snap-in mechanism
• Ferrule bearing spring loaded
• Not strain-relieved
• Integrated mechanical keying
Cleaning and Soldering Process for
Transmitter and Receiver
Special care must be taken to remove residuals from the sol-
dering and washing process, which can impact the mechanical
function. Avoid the use of aggressive organic solvents like
ketones, ethers, etc. Consult the supplier of the PAROLI mod-
ules and the supplier of the solder paste and flux for recom-
mended cleaning solvents.
The following common cleaning solvents will not affect the
module: deionized water, ethanol, and isopropyl alcohol. Air-
drying is recommended to a maximum temperature of 100°C.
Do not use ultrasonics.
During soldering, heat must be applied to the leads only, to
ensure that the case temperature never exceeds 100°C. The
module must be mounted with a hot-bar soldering process
using a SnPb solder type, e.g.. S-Sn63Pb37E, in accordance
with ISO 9435.
Fiber Optics
V23814/15-U1306-M130 Parallel Optical Link: PAROLI™ Tx/Rx AC, 1.6 Gbit/s
7