V23815-U1306-MXXX Datasheet, PDF (1/9 Pages) Infineon Technologies AG – Parallel Optical Link: PAROLI T X AC, 1.6 Gbit/s

V23814-U1306-M130
Parallel Optical Link: PAROLI™ Tx AC, 1.6 Gbit/s
V23815-U1306-M130
Parallel Optical Link: PAROLI™ Rx AC, 1.6 Gbit/s
Preliminary
Dimensions in (mm) inches
(58.1) 2.287
A
Reference point for case temperature ^(1.5)
measurement (center of fin width)
.059
(1.5)
(7.5)
.059 .295
A—A
(14) .551
(13.5)
0.531
(.13)
(6.8) .268 .005
(∅1.3 max)
∅.051 max
(22.7) .894
(0.27)
.011
4xM2
(7) .276
(33.89) 1.334
A
(12.73)
(∅3) ^.501
∅.118
(1.2)
.047
(∅2.5)
∅.098
(1.0)
.039
(14.9) .587
(17.9) .705
FEATURES
• Power supply 3.3 V
• Low voltage differential signal electrical interface (LVDS)
• 12 electrical data channels
• Asynchronous, AC-coupled optical link
• 12 optical data channels
• Transmission data rate of 250-1600 Mbit/s per channel,
total link data rate up to 19 Gbit/s
• Transmission distance up to 200m
• Transmitter: 840 nm VCSEL (Vertical Cavity Surface Emit-
ting Laser) technology
• Receiver: 840 nm PIN diode array
• Fiber ribbon: 62.5 µm graded index multimode fiber
• MT based optical port
• SMD technology
• Transmitter: Class 1 FDA and Class 3A IEC laser safety
compliant
APPLICATIONS
Telecommunication
• Switching equipment
• Access network
Data Communication
• Interframe (rack-to-rack)
• Intraframe (board-to-board)
• On board (optical backplane)
• Interface to SCI and HIPPI 6400 standards
Absolute Maximum Ratings
Stress beyond the values stated below may cause permanent
damage to the device. Exposure to absolute maximum rating
conditions for extended periods of time may affect
device reliability.
Supply Voltage (V_CC–V_EE).................................... –0.3 V to 4.5 V
Data/Control Input Levels (V_IN)⁽¹⁾................ –0.5 V to V_CC+0.5 V
LVDS Input Differential Voltage (|V_ID|)⁽²⁾ .............................. 2.0 V
Operating Case Temperature (T_CASE)⁽³⁾ ............... 0°C to 80°C
Storage Ambient Temperature (T_STG)................ –20°C to 100°C
Operating Moisture ............................................... 20% to 85%
Storage Moisture.................................................... 20% to 85%
Soldering Conditions Temp/Time (T_SOLD, t_SOLD)⁽⁴⁾ ....260°C/10s
ESD Resistance (all pins to V_EE, human body model)⁽⁵⁾...... 1 kV
Notes
1. At LVDS and LVCMOS inputs.
2. |V_ID|=|(input voltage of non-inverted input minus input voltage of
inverted input)|.
3. Measured at case temperature reference point (see dimensional
drawing).
4. Hot bar soldering.
5. To avoid electrostatic damage the handling precautions as for MOS
devices must be taken into account.
Fiber Optics
SEPTEMBER 1999