English
Language : 

TLE7368_10 Datasheet, PDF (17/41 Pages) Infineon Technologies AG – Next Generation Micro Controller Supply
TLE7368
General Product Characteristics
Electrical Characteristics (cont’d)
VIN = VIN_STBY = 13.5 V, Tj = -40 °C to +150 °C,
VCCP = 9.0 V; SEL_STBY = Q_STBY; all voltages with respect to ground.
Pos. Parameter
Symbol
Limit Values
Unit
Conditions
Min. Typ. Max.
4.4.65 Load regulation
∆VQ_ STBY
–
–
–
–
4.4.66 Line regulation
∆VQ_ STBY
–
–
4.4.67 Power supply ripple
PSRRQ_STBY 60
–
rejection
4.4.68 Output capacitor
CQ_STBY
0.47 –
4.4.69 Output capacitor
ESR
0
–
CQ_STBY
Device Enable Blocks and Quiescent Current
5
V/A IQ_STBY = 100µA to 10 mA
VIN_STBY > 4.5 V;
SEL_STBY = Q_STBY
VQ_STBY = 1.0V
10
V/A IQ_STBY = 100µA to 10 mA
VIN_STBY > 4.5 V;
SEL_STBY = GND
VQ_STBY = 2.6V
5
mV/V –
–
dB VIN_STBY, ripple pp = 500 mV;
fIN_STBY, ripple = 100 Hz;
IQ_STBY = 5 mA;
CQ_STBY = 1 µF ceramic X7R;1)
2
µF
1) 5)
0.5
Ω
at 10 kHz;1)
4.4.70 Ignition turn on
threshold
VEN_IGN, on
–
–
4.0 V Device operating
4.4.71 Ignition turn off
threshold
4.4.72 Ignition pull-down
resistor current
VEN_IGN, off 2.0
–
IEN_IGN
-100 –
–
V Only stand-by regulators are
active if VEN_IGN < VEN_IGN, off
and VEN_uC < VEN_uC, off
–
µA VEN_IGN = 13.5 V
4.4.73
4.4.74
Turn on threshold
Turn off threshold
4.4.75 Pull-down resistor
current
VEN_uC, on
–
–
VEN_uC, off
0.8
–
IEN_uC
-30 –
2.0 V Device operating
–
V Only stand-by regulators are
active if VEN_IGN < VEN_IGN, off
and VEN_uC < VEN_uC, off
–
µA VEN_uC = 5 V
4.4.76 Quiescent current
Iq = IIN_STBY - -120 –
–
µA VEN_uC = VEN_IGN = 0 V;
IQ_STBY
SEL_STBY = Q_STBY;
MON_STBY = H;
IQ_STBY = 100 µA; Tj < 125 °C
4.4.77 Quiescent current
Iq = IIN_STBY - -130 –
–
µA VEN_uC = VEN_IGN = 0 V;
IQ_STBY
SEL_STBY = GND;
MON_STBY = H;
IQ_STBY = 100 µA; Tj < 125 °C
4.4.78 Quiescent current
Iq, IN
-10 –
–
µA VEN_uC = VEN_IGN = 0 V;
VIN_STBY = 0 V;
Tj < 125 °C
Reset Generator RO_1 Monitoring Q_LDO1
Data Sheet
17
Rev. 2.1, 2010-11-22