82P33810 Datasheet, PDF (1/13 Pages) Integrated Device Technology – Composite clock inputs

Synchronization Management Unit for IEEE
1588 and Synchronous Ethernet
82P33810
SHORT FORM DATA SHEET
HIGHLIGHTS
• Synchronization Management Unit (SMU) provides tools to manage
physical layer and packet based synchronous clocks for IEEE 1588 /
PTP Telecom Profile applications
• Supports independent IEEE 1588 and Synchronous Ethernet
(SyncE) timing paths
• Combo mode provides SyncE physical layer frequency support for
IEEE 1588 Telecom Boundary Clocks (T-BC) and Telecom Time
Slave Clocks (T-TSC) per G.8273.2
• Digital PLL 1 (DPLL1) and DPLL 2 can be configured as Digitally
Controlled Oscillators (DCOs) for PTP clock synthesis
• DCO frequency resolution is [(77760 / 1638400) * 2^-48] or
~1.686305041e-10 ppm
• DPLL1 and DPLL2 generate G.8262 compliant SyncE clocks
• Two independent Time of Day (ToD) counters/time accumulators, one
associated with each of DPLL1 and DPLL2, can be used to track dif-
ferences between the two time domains and to time-stamp external
events
• DPLL3 performs rate conversions to frequency synchronization inter-
faces or for other general purpose timing applications
• APLL1 and APLL2 generate clocks with jitter < 1 ps RMS (12 kHz to
20 MHz) for: 1000BASE-T and 1000BASE-X
• Fractional-N input dividers support a wide range of reference fre-
quencies
• Locks to 1 Pulse Per Second (PPS) references
• It can be configured from an external EEPROM after reset
FEATURES
• Composite clock inputs (IN1 and IN2) accept 64 kHz synchronization
interface signals per ITU-T G.703
• Differential reference inputs (IN3 to IN8) accept clock frequencies
between 1 PPS and 650 MHz
• Single ended inputs (IN9 to IN14) accept reference clock frequencies
between 1 PPS and 162.5 MHz
• Loss of Signal (LOS) pins (LOS0 to LOS3) can be assigned to any
clock reference input
• Reference monitors qualify/disqualify references depending on activ-
ity, frequency and LOS pins
• Automatic reference selection state machines select the active refer-
ence for each DPLL based on the reference monitors, priority tables,
revertive and non-revertive settings and other programmable settings
• Fractional-N input dividers enable the DPLLs to lock to a wide range
of reference clock frequencies including: 10/100/1000 Ethernet, 10G
Ethernet, OTN, SONET/SDH, PDH, TDM, GSM, CPRI and GNSS
frequencies
• Any reference input (IN3 to IN14) can be designated as external sync
pulse inputs (1 PPS, 2 kHz, 4 kHz or 8 kHz) associated with a select-
able reference clock input
• FRSYNC_8K_1PPS and MFRSYNC_2K_1PPS output sync pulses
that are aligned with the selected external input sync pulse input and
frequency locked to the associated reference clock input
• DPLL1 and DPLL2 can be configured with bandwidths between 0.09
mHz and 567 Hz
• DPLL1 and DPLL2 lock to input references with frequencies between
1 PPS and 650 MHz
• DPLL3 locks to input references with frequencies between 8 kHz and
650 MHz
• DPLL1 and DPLL2 comply with ITU-T G.8262 for Synchronous
Ethernet Equipment Clock (EEC), and G.813 for Synchronous Equip-
ment Clock (SEC); and Telcordia GR-253-CORE for Stratum 3 and
SONET Minimum Clock (SMC)
• DPLL1 and DPLL2 generate clocks with PDH, TDM, GSM, CPRI/
OBSAI, 10/100/1000 Ethernet and GNSS frequencies; these clocks
are directly available on OUT1 and OUT8
• DPLL1 and DPLL2 can be configured as DCOs to synthesize IEEE
1588 clocks
• DPLL3 generates N x 8 kHz clocks up to 100 MHz that are output on
OUT10 and OUT11
• APLL1 and APLL2 can be connected to DPLL1 or DPLL2
• APLL1 and APLL2 generate 10/100/1000 Ethernet, 10G Ethernet, or
SONET/SDH frequencies
• Any of eight common TCXO/OCXO frequencies can be used for the
System Clock: 10 MHz, 12.8 MHz, 13 MHz, 19.44 MHz, 20 MHz,
24.576 MHz, 25 MHz or 30.72 MHz
• The I2C slave, SPI or the UART interface can be used by a host pro-
cessor to access the control and status registers
• The I2C master interface can automatically load a device configura-
tion from an external EEPROM after reset
• DPLL1 or DPLL3 can be connected to an internal composite clock
generator that outputs its 64 kHz synchronization signal on OUT8
• Differential outputs OUT3 to OUT6 output clocks with frequencies
between 1 PPS and 650 MHz
• Single ended outputs OUT1, OUT2, OUT7 and OUT8 output clocks
with frequencies between 1 PPS and 125 MHz
• Single ended outputs OUT10 and OUT11 output clocks N*8kHz multi-
ples up to 100 MHz
• DPLL1 and DPLL2 support independent programmable delays for
each of IN3 to IN14; the delay for each input is programmable in
steps of 0.61 ns with a range of ~±78 ns
• The input to output phase delay of DPLL1 and DPLL2 is programma-
ble in steps of 0.0745 ps with a total range of ±20 μs
• The clock phase of each of the output dividers for OUT1 (from
APLL1) to OUT8 is individually programmable in steps of ~200 ps
with a total range of +/-180°
• 1149.1 JTAG Boundary Scan
• 144-pin CABGA green package
82P33810 REVISION 2 12/08/14
1
©2014 Integrated Device Technology, Inc.