IC-JX Datasheet, PDF (4/36 Pages) IC-Haus GmbH – 16-FOLD 24 V HIGH-SIDE DRIVER WITH μC INTERFACE

iC-JX
16-FOLD 24 V HIGH-SIDE DRIVER WITH µC INTERFACE
Rev C1, Page 4/36
ABSOLUTE MAXIMUM RATINGS
Beyond these values damage may occur; device operation is not guaranteed. Absolute Maximum Ratings are no Operating Conditions.
Integrated circuits with system interfaces, e.g. via cable accessible pins (I/O pins, line drivers) are per principle endangered by injected
interferences, which may compromise the function or durability. The robustness of the devices has to be verified by the user during system
development with regards to applying standards and ensured where necessary by additional protective circuitry. By the manufacturer
suggested protective circuitry is for information only and given without responsibility and has to be verified within the actual system with
respect to actual interferences.
(Legend: x = 1..16, y = 1..4)
Item Symbol Parameter
No.
Conditions
Min.
Unit
Max.
G001 VCC, VDD Supply Voltage
-0.3
6
V
G002 VBy
G003 V(IOx)
Driver Supply Voltage
Voltages at IO1...16
IOx = off; see additional remark ¹
-0.3
40
V
-10
40
V
G004 Idc(IOx) Current in IO1...16
see Figure 1
-500
150
mA
G005 Ipk(IOx) Pulse current in IO1...16
IOx = hi, τ = 2 ms, T ≤ 2 s
see Figure 2
-1.0
A
G006 Imax()
Current in VCC, VDD
-100
100
mA
G007 Imax(VBy) Current in VB1...4
-8
8
A
G008 Ic()
Current in NCS, NWR, NRD, A0...4, D0...7 with input function
D0...7, NRES, CLK, BLFQ, POE, NSP,
RSET, VREF
-20
20
mA
G009 I()
Current in D0...7, NINT,
D0...7 with output function
-25
25
mA
G010 Ilu()
Pulse current in NCS, NWR, NRD,
A0...4, D0...7, NRES, CLK, BLFQ,
NINT, NSP, POE, IO1...16, RSET,
VREF (latch up test)
Pulse width < 10 µs,
all inputs / outputs open
-100
100
mA
G011 Vd()
ESD-voltage, all pins
HBM 100 pF discharged over 1.5 kΩ
2
kV
G012 Vb()
Burst transients at IO1...16
after IEC 1000-4-4
4
kV
G013 Tj
Chip temperature
-40
150
°C
G014 Ts
Storage temperature
-40
150
°C
1) _{If the voltage supplies can not be guaranteed to be present at the time signals appear at the pins IO1..IO16,}
additional diodes or sufficient current limiting ohmic resistors have to be connected in series to the IO-pins to
prevent reverse back biasing of the device.
THERMAL DATA
Operating conditions: VCC = VDD = 3 ... 5.5 V, VBy = 12 ... 36 V, GNDA = GNDD = 0 V, all inputs on defined logic states (high or low)
Item Symbol Parameter
No.
Conditions
Unit
Min. Typ. Max.
T01 Ta
Ambient temperature
extended temperature range on request
-40
85 °C
T02 Rthja
Thermal resistance chip/ambient
package mounted on PCB
55
K/W
All voltages are referenced to ground unless otherwise stated.
All currents flowing into the device pins are positive; all currents flowing out of the device pins are negative.