IC-JX Datasheet, PDF (14/36 Pages) IC-Haus GmbH – 16-FOLD 24 V HIGH-SIDE DRIVER WITH μC INTERFACE

iC-JX
16-FOLD 24 V HIGH-SIDE DRIVER WITH µC INTERFACE
Rev C1, Page 14/36
Register Overview
Adress
A(4...0) A4 A3 A2 A1 A0 Write
Read
0x00 0 0 0 0 0 -
Input Register A^1,2
0x01 0 0 0 0 1 -
Input Register B^1,2
0x02 0 0 0 1 0 -
Input Change Message A^1,3
0x03 0 0 0 1 1 -
Input Change Message B^1,3
0x04 0 0 1 0 0 -
Interrupt Message Register A
0x05 0 0 1 0 1 -
Interrupt Message Register B
0x06 0 0 1 1 0 -
Overcurrent Message A^1,4
0x07 0 0 1 1 1 -
Overcurrent Message B^1,4
0x08 0 1 0 0 0 -
Overcurrent Status A¹
0x09 0 1 0 0 1 -
Overcurrent Status B¹
0x0A 0 1 0 1 0 -
A/D-Converter Data 1
0x0B 0 1 0 1 1 -
A/D-Converter Data 2
0x0C 0 1 1 0 1
Output Register A¹
0x0D 0 1 1 1 0
Output Register B¹
0x0E 0 1 1 1 1
Flash Pulse Enable A¹
0x0F 1 0 0 0 0
Flash Pulse Enable B¹
0x10 1 0 0 0 1
Interrupt-Enable Input Change A^1,5
0x11 1 0 0 1 0
Interrupt-Enable Input Change B^1,5
0x12 1 0 0 1 1
Interrupt-Enable Overcurrent A¹
0x13 1 0 1 0 0
Interrupt-Enable Overcurrent B¹
0x14 1 0 1 0 1
Control Word 1A (I/O Filter)¹
0x15 1 0 1 1 0
Control Word 1B (I/O Filter)¹
0x16 1 0 1 1 1
Control Word 2A (I/O Pin Functions)¹
0x17 1 1 0 0 0
Control Word 2B (I/O Pin Functions)¹
0x18 1 1 0 0 1
Control Word 3A (Flash Pulse Settings)¹
0x19 1 1 0 1 0
Control Word 3B (Flash Pulse Settings)¹
0x1A 1 1 0 1 1
Control Word 4 (Overcurrent Filter Settings)
0x1B 1 1 1 0 0
Control Word 5 (I/O Stage Selection for AD Converter
0x1C 1 1 1 0 1
Control Word 6 (AD Converter Settings)
0x1D 0 1 1 0 0 -
Interconnection Error, Device-ID
0x1E 1 1 1 1 0
Test Register 1
0x1F 1 1 1 1 1
Test Register 2
Table 7: Register assignment
1. A: I/O-Stages 1...8, B: I/O-Stages 9...16
2. Reads the inpus or reads back the outputs, depending on I/O pin mode
3. For I/O pins in input mode (register is ’0’ in output mode)
4. For I/O pins in output mode (register is ’0’ in input mode)
5. Only writable in input mode