FH12-6S-0.5SH Datasheet, PDF (13/19 Pages) Hirose Electric – 0.5mm and 1mm Pitch Connectors For FPC/FFC

s1mm Pitch Type Bottom Contact Type
2.3
A
1.0
(0.2)
B
C
E
Mated Cross-sectional Diagram
(2.1)
FPC/FFC Contact Surface
(3.1)
(1.3)
D
4.6
5.6
Unit:mm
Part Number
CL No. Number of Contacts A
B
C
D
E
FH12-05S-1SH
586-0591-6
5
FH12-06S-1SH
586-0607-4
6
04
08.6 09.6 06.07 2.3
05
09.6 10.6 07.07 2.3
FH12-07S-1SH
586-0535-5
7
FH12-08S-1SH
586-0579-0
8
FH12-09S-1SH
586-0540-5
9
06
10.6 11.6 08.07 2.3
07
11.6 12.6 09.07 2.3
08
12.6 13.6 10.07 2.3
FH12-11S-1SH
586-0668-9
11
FH12-16S-1SH
586-0536-8
16
FH12-22S-1SH
586-0547-4
22
10
14.6 15.6 12.07 2.3
15
19.6 20.6 17.07 2.3
21
25.6 26.6 23.07 2.3
FH12-26S-1SH
586-0592-9
26
FH12-10(4)SA-1SH 586-0537-0
4
FH12-14(6)SA-1SH 586-0538-3
6
FH12-18(8)SA-1SH 586-0539-6
8
FH12-22(10)SA-1SH 586-0541-8
10
FH12-24(11)SA-1SH 586-0542-0
11
FH12-30(14)SA-1SH 586-0543-3
14
FH12-40(19)SA-1SH 586-0546-1
19
FH12-50(24)SA-1SH 586-0548-7
24
25
29.6 30.6 27.07 2.3
03
08.1 09.1 05.57 2.8
05
10.1 11.1 07.57 2.8
07
12.1 13.1 09.57 2.8
09
14.1 15.1 11.57 2.8
10
15.1 16.1 12.57 2.8
13
18.1 19.1 15.57 2.8
18
23.1 24.1 20.57 2.8
23
28.1 29.1 25.57 2.8
Note 1: Embossed tape reel packaging (2,000 pieces/reel).
Order by number of reels.
Note 2: The 1mm version of FH12 is constructed by loading every other contact into the 0.5mm housing.
When a housing designed for an odd number of 0.5mm pitch contacts is used; the spacing from the
edge to the first contact on either side is the same as the distance between each contact, 1.0mm.
Hirose considers this design to be a standard-type 1.0mm connector.
Note 2: An eccentric-type connector using a housing designed for an even number of 0.5mm pitch contacts
and consequently one side has 1.5mm distance from the edge to the first contact. (See FPC/FFC
dimensional drawing on page 19) The part number for the eccentric type describes the size of the
0.5mm housing used and lists the number of 1.0mm pitch contacts in parentheses () as shown in the
above table.
18