MC33580 Datasheet, PDF (8/38 Pages) Freescale Semiconductor, Inc – Quad High-Side Switch (Quad 15 mΩ)

ELECTRICAL CHARACTERISTICS
STATIC ELECTICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics (continued)
Characteristics noted under conditions 6.0 V ≤ V_PWR ≤ 27 V, 4.5 V ≤ V_DD ≤ 5.5 V, -40°C ≤ T_A ≤ 125°C, GND = 0 V unless
otherwise noted. Typical values noted reflect the approximate parameter means at T_A = 25°C under nominal conditions unless
otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
OUTPUTS (HS0, HS1, HS2, HS3) (continued)
Output Fault Detection Threshold
Output Programmed OFF
V_OFD(THRES)
V
2.0
3.0
4.0
Output Negative Clamp Voltage
0.5 A < I_HS[0:3] < 2.0 A, Output OFF
V_CL
V
- 20
–
-16
Overtemperature Shutdown ⁽¹³⁾
Overtemperature Shutdown Hysteresis ⁽¹³⁾
T_SD
155
175
190
°C
T_SD(HYS)
5.0
–
20
°C
CONTROL INTERFACE (SCLK, SI, SO, IN[0:3], RST, WAKE, FS, CS, FSI)
Input Logic High Voltage ⁽¹⁴⁾
Input Logic Low Voltage ⁽¹⁴⁾
Input Logic Voltage Hysteresis ⁽¹⁵⁾
V_IH
0.7 V_DD
–
–
V
V_IL
–
–
0.2 V_DD
V
V_IN(HYS)
100
850
1200
mV
Input Logic Pulldown Current (SCLK, SI, IN[0:3], VIN>0.2 VDD)
RST Input Voltage Range
SO, FS Tri-State Capacitance ⁽¹⁵⁾
I_DWN
V_RST
C_SO
5.0
–
20
µA
4.5
5.0
5.5
V
–
–
20
pF
Input Logic Pulldown Resistor (RST) and WAKE
Input Capacitance ⁽¹⁵⁾
Wake Input Clamp Voltage ⁽¹⁶⁾
I_CL(WAKE) < 2.5 mA
R_DWN
100
200
400
kΩ
C_IN
–
4.0
12
pF
V_CL(WAKE)
V
7.0
–
14
Wake Input Forward Voltage
I_CL(WAKE) = -2.5 mA
V_F(WAKE)
V
- 2.0
–
- 0.3
SO High-State Output Voltage
I_OH = 1.0 mA
FS, SO Low-State Output Voltage
I_OL = -1.6 mA
V_SOH
V
0.8 V_DD
–
–
V_SOL
V
–
0.2
0.4
SO Tri-State Leakage Current
CS>=0.7VDD, 0<VSO<VDD
Input Logic Pullup Current (CS) ⁽¹⁷⁾
Vin < 0.7 VDD
I_SO(LEAK)
- 5.0
0
I_UP
5.0
–
µA
5.0
µA
20
Notes
13. Guaranteed by process monitoring. Not production tested.
14. Upper and lower logic threshold voltage range applies to SI, CS, SCLK, RST, IN[0:3], and WAKE input signals. The WAKE and RST
signals may be supplied by a derived voltage referenced to V_PWR.
15. Ads Input capacitance of SI, CS, SCLK, RST, and WAKE. This parameter is guaranteed by process monitoring but is not production
tested.
16. The current must be limited by a series resistance when using voltages > 7.0 V.
17. Pullup current is with CS OPEN. CS has an active internal pullup to V_DD.
33580
8
Analog Integrated Circuit Device Data
Freescale Semiconductor