|
MC9S08PT16 Datasheet, PDF (1/33 Pages) Freescale Semiconductor, Inc – MC9S08PT16 | |||
|
Freescale Semiconductor
Data Sheet: Technical Data
MC9S08PT16 Series
Support: MC9S08PT16 and
MC9S08PT8
Features
⢠8-Bit S08 central processor unit (CPU)
â Up to 20 MHz bus at 2.7 V to 5.5 V across
temperature range of -40 °C to 105 °C
â Supporting up to 40 interrupt/reset sources
â Supporting up to four-level nested interrupt
â On-chip memory
â Up to 16 KB flash read/program/erase over full
operating voltage and temperature
â Up to 256 byte EEPROM; 2-byte erase sector;
program and erase while executing flash
â Up to 2048 byte random-access memory (RAM)
â Flash and RAM access protection
⢠Power-saving modes
â One low-power stop mode; reduced power wait
mode
â Peripheral clock enable register can disable clocks to
unused modules, reducing currents; allows clocks to
remain enabled to specific peripherals in stop3 mode
⢠Clocks
â Oscillator (XOSC) - loop-controlled Pierce
oscillator; crystal or ceramic resonator range of
31.25 kHz to 39.0625 kHz or 4 MHz to 20 MHz
â Internal clock source (ICS) - containing a frequency-
locked-loop (FLL) controlled by internal or external
reference; precision trimming of internal reference
allowing 1% deviation across temperature range of 0
°C to 70 °C and 2% deviation across temperature
range of -40 °C to 105 °C; up to 20 MHz
⢠System protection
â Watchdog with independent clock source
â Low-voltage detection with reset or interrupt;
selectable trip points
â Illegal opcode detection with reset
â Illegal address detection with reset
Document Number: MC9S08PT16
Rev. 1, 7/4/2012
MC9S08PT16
⢠Development support
â Single-wire background debug interface
â Breakpoint capability to allow three breakpoints
setting during in-circuit debugging
â On-chip in-circuit emulator (ICE) debug module
containing two comparators and nine trigger modes
⢠Peripherals
â ACMP - one analog comparator with both positive
and negative inputs; separately selectable interrupt
on rising and falling comparator output; filtering
â ADC - 12-channel, 12-bit resolution; 2.5 µs
conversion time; data buffers with optional
watermark; automatic compare function; internal
bandgap reference channel; operation in stop mode;
optional hardware trigger
â CRC - programmable cyclic redundancy check
module
â FTM - two flex timer modulators modules including
one 6-channel and one 2-channel ones; 16-bit
counter; each channel can be configured for input
capture, output compare, edge- or center-aligned
PWM mode
â IIC - One inter-integrated circuit module; up to 400
kbps; multi-master operation; programmable slave
address; supporting broadcast mode and 10-bit
addressing
â MTIM - One modulo timer with 8-bit prescaler and
overflow interrupt
â RTC - 16-bit real timer counter (RTC)
â SCI - two serial communication interface (SCI/
UART) modules optional 13-bit break; full duplex
non-return to zero (NRZ); LIN extension support
â SPI - one 8-bit serial peripheral interface (SPI)
modules; full-duplex or single-wire bidirectional;
master or slave mode
â TSI - supporting up to 16 external electrodes;
configurable software or hardware scan trigger; fully
support freescale touch sensing software library;
capability to wake MCU from stop3 mode
Freescale reserves the right to change the detail specifications as may be
required to permit improvements in the design of its products.
© 2011â2012 Freescale Semiconductor, Inc.
|
▷ |