XR16L2752 Datasheet, PDF (32/49 Pages) Exar Corporation – 2.25V TO 5.5V DUART WITH 64-BYTE FIFO

XR16L2752
2.25V TO 5.5V DUART WITH 64-BYTE FIFO
xr
REV. 1.2.1
MSR[3]: Delta CD# Input Flag
• Logic 0 = No change on CD# input (default).
• Logic 1 = Indicates that the CD# input has changed state since the last time it was monitored. A modem
status interrupt will be generated if MSR interrupt is enabled (IER bit-3).
MSR[4]: CTS Input Status
CTS# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto
CTS (EFR bit-7). Auto CTS flow control allows starting and stopping of local data transmissions based on the
modem CTS# signal. A HIGH on the CTS# pin will stop UART transmitter as soon as the current character has
finished transmission, and a LOW will resume data transmission. Normally MSR bit-4 bit is the complement of
the CTS# input. However in the loopback mode, this bit is equivalent to the RTS# bit in the MCR register. The
CTS# input may be used as a general purpose input when the modem interface is not used.
MSR[5]: DSR Input Status
Normally this bit is the complement of the DSR# input. In the loopback mode, this bit is equivalent to the DTR#
bit in the MCR register. The DSR# input may be used as a general purpose input when the modem interface is
not used.
MSR[6]: RI Input Status
Normally this bit is the complement of the RI# input. In the loopback mode this bit is equivalent to bit-2 in the
MCR register. The RI# input may be used as a general purpose input when the modem interface is not used.
MSR[7]: CD Input Status
Normally this bit is the complement of the CD# input. In the loopback mode this bit is equivalent to bit-3 in the
MCR register. The CD# input may be used as a general purpose input when the modem interface is not used.
4.11 Scratch Pad Register (SPR) - Read/Write
This is a 8-bit general purpose register for the user to store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle.
4.12 Enhanced Mode Select Register (EMSR)
This register replaces SPR (during a Write) and is accessible only when FCTR[6] = 1.
EMSR[1:0]: Receive/Transmit FIFO Count (Write-Only)
When Scratchpad Swap (FCTR[6]) is asserted, EMSR bits 1-0 controls what mode the FIFO Level Counter is
operating in.
TABLE 12: SCRATCHPAD SWAP SELECTION
FCTR[6] EMSR[1] EMSR[0] Scratchpad is
0
X
X Scratchpad
1
0
0 RX FIFO Counter Mode
1
0
1 TX FIFO Counter Mode
1
1
0 RX FIFO Counter Mode
1
1
1 Alternate RX/TX FIFO
Counter Mode
During Alternate RX/TX FIFO Counter Mode, the first value read after EMSR bits 1-0 have been asserted will
always be the RX FIFO Counter. The second value read will correspond with the TX FIFO Counter. The next
value will be the RX FIFO Counter again, then the TX FIFO Counter and so on and so forth.
EMSR[2]: Reserved
EMSR[3]: Automatic RS485 Half-Duplex Control Output Inversion
• Logic 0 = RTS# output is a logic 0 during TX and a logic 1 during RX (default, compatible with 16C2850).
• Logic 1 = RTS# output is a logic 1 during TX and a logic 0 during RX.
32