SGU01G64A1BG1SA-BBR Datasheet, PDF (7/16 Pages) List of Unclassifed Manufacturers – 1024MB DDR3 . SDRAM UDIMM

Data Sheet
Rev.1.1 11.04.2013
I_DD Specifications and Conditions
(0°C ≤ TCASE ≤ + 85°C°, VDDQ = +1.5V ± 0.075V, VDD = +1.5V ± 0.075V)
Parameter
& Test Condition
Symbol
12800-CL11
OPERATING CURRENT *) :
One device bank Active-Precharge;
I_DD0
280
t_RC= t_RC (I_DD); t_CK = t_CK (I_DD); CKE is HIGH, CS# is HIGH
between valid commands;
DQ inputs changing once per clock cycle; Address and
control inputs changing once every two clock cycles
OPERATING CURRENT *) :
One device bank; Active-Read-Precharge;
I_DD1
360
I_OUT = 0mA; BL = 4, CL = CL (I_DD), AL = 0;
t_CK = t_CK (I_DD), t_RC= t_RC (I_DD), t_RAS = t_RAS MIN (I_DD),
t_RCD = t_RCD (I_DD); CKE is HIGH, CS# is HIGH between
valid commands; Address inputs changing once every
two clock cycles; Data Pattern is same as I_DD4W
PRECHARGE POWER-DOWN
CURRENT:
Fast Exit
I_DD2P
96
All device banks idle; Power-down mode;
t_CK = t_CK (I_DD); CKE is LOW; All Control
Slow Exit
80
and Address bus inputs are not changing;
DQ’s are floating at V_REF
PRECHARGE QUIET STANDBY CURRENT:
All device banks idle;
I_DD2Q
120
t_CK = t_CK (I_DD); CKE is HIGH, CS# is HIGH;
All Control and Address bus inputs are not changing;
DQ’s are floating at V_REF
PRECHARGE STANDBY CURRENT:
All device banks idle;
I_DD2N
120
t_CK = t_CK (I_DD); CKE is HIGH, CS# is HIGH;
All other Control and Address bus inputs are changing
once every two clock cycles; DQ inputs changing once
per clock cycle
ACTIVE POWER-DOWN CURRENT:
I_DD3P
120
All device banks open; t_CK = t_CK (I_DD); CKE is LOW; All
Control and Address bus inputs are not changing;
DQ’s are floating at V_REF (always fast exit)
ACTIVE STANDBY CURRENT:
All device banks open; t_CK = t_CK (I_DD),
I_DD3N
160
t_RAS = t_RAS MAX (I_DD), t_RP = t_RP (I_DD);
CKE is HIGH, CS# is HIGH between valid commands;
All other Control and Address bus inputs are changing
once every two clock cycles; DQ inputs changing once
per clock cycle
OPERATING READ CURRENT:
All device banks open, Continuous burst reads; One
I_DD4R
600
module rank active; I_OUT = 0mA; BL = 4, CL = CL (I_DD),
AL = 0; t_CK = t_CK (I_DD), t_RAS = t_RAS MAX (I_DD), t_RP = t_RP
(I_DD); CKE is HIGH, CS# is HIGH between valid
commands; Address bus inputs are changing once
every two clock cycles; DQ inputs changing once per
clock cycle
max.
10600-CL9
280
336
96
80
120
120
120
160
520
Unit
8500-CL7
280
mA
320
mA
96
mA
80
120
mA
120
mA
120
mA
160
mA
440
mA
Swissbit AG
Industriestrasse 4
CH-9552 Bronschhofen
Fon: [phone]
Fax: [phone]
www.swissbit.com
eMail: [e-mail]
Page 7
of 16