ISE30-T1-25 Datasheet, PDF (5/21 Pages) List of Unclassifed Manufacturers – High Precision,2-color Display Digital Pressure Switch

ZSE30/ISE30 ^{High Precision,}
2-color Display Digital Pressure Switch Series
Specifications
ZSE30 (Vacuum/Low pressure) ISE30 (Positive pressure)
Rated pressure range
–100.0 to 100.0 kPa
0.000 to 1.000 MPa
Regulating pressure range
–101.0 to 101.0 kPa
–0.100 to 1.000 MPa
Proof pressure
500 kPa
1.5 MPa
Min. regulating unit
0.2 kPa
0.001 MPa
Fluid
Air, Inert gas, Non-flammable gas
Power supply voltage
12 to 24 VDC, Ripple (p-p) 10% or less (With power supply polarity protection)
Current consumption
Switch output ^{Note 1)}
45 mA or less (at no load)
NPN or PNP open collector output: 1 output
Max. load current
80 mA
Max. applied voltage
30 V (With NPN output)
Residual voltage
1 V or less (With load current of 80 mA)
Response time
2.5 ms or less (Response time selections with anti-chattering function: 20, 160, 640, 1280 ms)
Short circuit protection
Yes
Repeatability
±0.2% F.S. ±2 digit or less
±0.2% F.S. ±1 digit or less
Note 2)
Voltage output
Output voltage: 1 to 5 V ±2.5% F.S. or less (With rated pressure range)
Linearity: ±1% F.S. or less, Output impedance: Approx. 1 kΩ
Analog
output
Output current: 4 to 20 mA ±2.5% F.S. or less (With rated pressure range)
Note 3)
Linearity: ±1% F.S. or less
Current output
Maximum load impedance: 300 Ω with power supply voltage of 12 V;
600 Ω with power supply voltage of 24 V
Minimum load impedance: 50 Ω
Hysteresis mode
Hysteresis _{Window comparator mode}
Adjustable (can be set from 0)
Display
3 1/2 digit, 7-segment indicator, 2-color display (Red and green)
Sampling cycle: 5 times/s
Display accuracy
Indicator light
Temperature characteristics
±2% F.S. ±2 digit
±2% F.S. ±1 digit
(at 25°C ambient temperature) (at 25°C ambient temperature)
Light up when output is ON (Green)
±2% F.S. or less (based on 25°C)
Enclosure
IP40
Operating temperature range Operating: 0 to 50°C, Stored: –10 to 60°C (No freezing or condensation)
Operating humidity range
Operating and stored: 35 to 85% RH (No condensation)
Withstand voltage
1000 VAC for 1 min. between live parts and enclosure
Insulation resistance
Vibration resistance
50 MΩ or more between live parts and enclosure (at 500 VDC)
10 to 150 Hz, 1.5 mm or 20 m/s² amplitude in X, Y, Z directions for 2 hours each
Impact resistance
100 m/s² in X, Y, Z directions 3 times each
Standard
Compliant with CE Marking and UL (CSA) standards
Note 1) When switch output is selected, analog output is not available.
Note 2) When voltage output is selected, a simultaneous selection of switch output and current output is
not available.
Note 3) When current output is selected, a simultaneous selection of switch output and voltage output is
not available.
ZSE„
ISE„
PSE
ZI _SE3
PS
ZI _SE12
ZSP
ISA2
IS„
ZSM
PF2„
IF„
Data
Piping Specifications
Part
Port _{One-touch fitting}
size Straight type
One-touch fitting
Elbow type
Wetted part material
With lead wire
with connector (2 m)
Weight
Without lead wire
with connector
01
T1
C4H
C6H
N7H
C4L
C6L
N7L
R 1/8
M5 x 0.8
NPT 1/8
M5 x 0.8
—
—
—
—
—
—
—
—
ø4 mm
ø5/32 inch
ø6 mm
ø1/4 inch
—
—
—
—
—
—
—
—
ø4 mm
ø5/32 inch
ø6 mm
ø1/4 inch
Sensor pressure receiving area: Silicon, Piping port: C3602 (Electroless nickel plated), O-ring: HNBR
O-ring: NBR
O-ring: NBR, fitting: PBT
81 g
76 g
78 g
43 g
38 g
40 g
16-2-5