S-8261ABRMD-G3RT2G Datasheet, PDF (15/33 Pages) List of Unclassifed Manufacturers – BATTERY PROTECTION IC FOR 1-CELL PACK

Rev.5.3_00
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8261 Series
„ Test Circuits
Caution
Unless otherwise specified, the output voltage levels “H” and “L” at CO pin (V_CO) and DO pin (V_DO) are
judged by the threshold voltage (1.0 V) of the N-channel FET. Judge the CO pin level with respect to
V_VM and the DO pin level with respect to V_SS.
(1) Test Condition 1, Test Circuit 1
(Overcharge Detection Voltage, Overcharge Hysteresis Voltage)
The overcharge detection voltage (V_CU) is defined as the voltage between VDD and VSS at which V_CO goes from “H”
to “L” when the voltage V1 is gradually increased from the starting condition of V1 = 3.5 V. The overcharge
hysteresis voltage (V_HC) is then defined as the difference between the overcharge detection voltage (V_CU) and the
voltage between VDD and VSS at which V_CO goes from “L” to “H” when the voltage V1 is gradually decreased.
(2) Test Condition 2, Test Circuit 2
(Overdischarge Detection Voltage, Overdischarge Hysteresis Voltage)
The overdischarge detection voltage (V_DL) is defined as the voltage between VDD and VSS at which V_DO goes from
“H” to “L” when the voltage V1 is gradually decreased from the starting condition of V1 = 3.5 V and V2 = 0 V. The
overdischarge hysteresis voltage (V_HD) is then defined as the difference between the overdischarge detection
voltage (V_DL) and the voltage between VDD and VSS at which V_DO goes from “L” to “H” when the voltage V1 is
gradually increased.
(3) Test Condition 3, Test Circuit 2
(Overcurrent 1 Detection Voltage, Overcurrent 2 Detection Voltage, Load Short-Circuiting Detection Voltage)
The overcurrent 1 detection voltage (V_IOV1) is defined as the voltage between VM and VSS whose delay time for
changing V_DO from “H” to “L” lies between the minimum and the maximum value of the overcurrent 1 detection delay
time when the voltage V2 is increased rapidly (within 10 μs) from the starting condition V1 = 3.5 V and V2 = 0 V.
The overcurrent 2 detection voltage (V_IOV2) is defined as the voltage between VM and VSS whose delay time for
changing V_DO from “H” to “L” lies between the minimum and the maximum value of the overcurrent 2 detection delay
time when the voltage V2 is increased rapidly (within 10 μs) from the starting condition V1 = 3.5 V and V2 = 0 V.
The load short-circuiting detection voltage (V_SHORT) is defined as the voltage between VM and VSS whose delay time
for changing V_DO from “H” to “L” lies between the minimum and the maximum value of the load short-circuiting
detection delay time when the voltage V2 is increased rapidly (within 10 μs) from the starting condition V1 = 3.5 V
and V2 = 0 V.
(4) Test Condition 4, Test Circuit 2
(Charger Detection Voltage, Abnormal Charge Current Detection Voltage)
The charger detection voltage (V_CHA) is defined as the voltage between VM and VSS at which V_DO goes from “L” to
“H” when the voltage V2 is gradually decreased from 0 V after the voltage V1 is gradually increased from the starting
condition of V1 = 1.8 V and V2 = 0 V until the voltage V1 becomes V1 = V_DL + (V_HD / 2).
The charger detection voltage can be measured only in the product whose overdischarge hysteresis V_HD ≠ 0.
Set V1 = 3.5 V and V2 = 0 V. Decrease V2 from 0 V gradually. The voltage between VM and VSS when V_CO goes
from “H” to “L” is the abnormal charge current detection voltage. The abnormal charge current detection voltage has
the same value as the charger detection voltage (V_CHA).
(5) Test Condition 5, Test Circuit 2
(Normal Operation Current Consumption, Power-Down Current Consumption, Overdischarge Current Consumption)
With power-down function
The operating current consumption (I_OPE) is the current that flows through the VDD pin (I_DD) under the set conditions
of V1 = 3.5 V and V2 = 0 V (Normal status).
The power-down current consumption (I_PDN) is the current that flows through the VDD pin (I_DD) under the set
conditions of V1 = V2 = 1.5 V (Overdischarge status).
Without power-down function
The operating current consumption (I_OPE) is the current that flows through the VDD pin (I_DD) under the set conditions
of V1 = 3.5 V and V2 = 0 V (Normal status).
The Overdischarge current consumption (I_OPED) is the current that flows through the VDD pin (I_DD) under the set
conditions of V1 = V2 = 1.5 V (Overdischarge status).
Seiko Instruments Inc.
15