GX-5SU Datasheet, PDF (13/16 Pages) List of Unclassifed Manufacturers – Cylindrical Inductive Proximity Sensor Amplifier Built-in

807
GX-U Cylindrical Inductive Proximity Sensor
SERIES
GX-FU SERIES
GX-N SERIES
FIBER
SENSORS
PRECAUTIONS FOR PROPER USE
LASER
SENSORS
All models
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
LIGHT
CURTAINS
• Never use this product as a sensing device
for personnel protection.
• In case of using sensing devices for
personnel protection, use products which
meet laws and standards, such as OSHA,
ANSI or IEC etc., for personnel protection
applicable in each region or country.
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
Mounting
• The tightening torque should be under the value given below.
Mounting with a set screw
• Tighten with the cup-point of a set screw (M4).
<Non-threaded type>
Mounting hole process dimension
Set screw
C
(M4)
A
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
ENDOSCOPE
LASER
MARKERS
PLC /
TERMINALS
HUMAN
MACHINE
INTERFACES
ENERGY
CONSUMPTION
VISUALIZATION
COMPONENTS
FA
COMPONENTS
B
Model No. A (mm in) B (mm in) C (mm in) Tightening torque
GX-5SU(B) 5 to 30 0.197 to 1.181
3 0.118
ø5.5 ⁺
0.2
0
ø0.217
+
0.008
0
0.78 N·m
• Do not fix on the operation indicator or opposite to it.
Operation
indicator
Operation
indicator
Operation
indicator
Set
screw
Mounting with nut
<Shielded of threaded type>
Attached toothed
D
lock washer
<Non-shielded of threaded type>
Attached toothed
D
lock washer
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplifier
Built-in
Amplifier-
separated
GX-F/H
GXL
GL
GX-U/GX-FU/
GX-N
GX
Mounting plate
Mounting plate
Model No.
GX-8MU(B)
GX-12MU(B)
GX-F12MU-J
GX-N12M(B)
GX-18MU(B)
GX-F18MU-J
GX-N18M(B)
GX-30MU(B)
GX-F30MU-J
GX-N30M(B)
GX-8MLU(B)
GX-12MLU(B)
GX-N12ML(B)
GX-18MLU(B)
GX-N18ML(B)
GX-30MLU(B)
GX-N30ML(B)
Dimension D (mm in)
3 to 10.3 0.118 to 0.406
10.3 0.406 or more
3.5 to 13.5 0.138 to 0.531
13.5 0.531 or more
4 to 18 0.157 to 0.709
18 0.709 or more
5 to 21 0.197 to 0.827
21 0.827 or more
12 0.472 or more
15 0.591 or more
25 0.984 or more
30 1.181 or more
Tightening torque
5.9 N·m
11.8 N·m
10 N·m
20 N·m
45 N·m
80 N·m
80 N·m
180 N·m
11.8 N·m
20 N·m
80 N·m
180 N·m
Note: Mount such that the nuts do not protrude from the threaded portion.
• The root truncation of the threads is shallow owing to
strengthening of the sensors against tightening.
When tapping holes on equipment to fix the sensors, the
prepared holes must be value in the table below.
Sensor
Tapping holes
Tap
Model No.
GX-8MU(B)
GX-8MLU(B)
GX-12MU(B)
GX-12MLU(B)
GX-F12MU-J
GX-N12M(B)
GX-N12ML(B)
Prepared hole
ø7.2 mm
ø0.283 in
ø11.2 mm
ø0.441 in
Refer to General precautions.
Distance from surrounding metal
• As metal around the sensor may affect the sensing
performance, pay attention to the following points.
Influence of surrounding metal
• The surrounding metal will affect the sensing performance.
Keep the minimum distance specified in the table below.
Model No.
E (mm in)
E
GX-5SU(B)
4.5 0.177
GX-8MU(B)
4.5 0.177
GX-12MU(B)
GX-F12MU-J
GX-N12M(B)
GX-18MU(B)
GX-F18MU-J
GX-N18M(B)
GX-30MU(B)
GX-F30MU-J
GX-N30M(B)
8 0.315
20 0.787
40 1.575
GX-8MLU(B)
8 0.315
GX-12MLU(B)
GX-N12ML(B)
22 0.866
GX-18MLU(B)
GX-N18ML(B)
45 1.772
GX-30MLU(B)
GX-N30ML(B)
75 2.953
Embedding of the sensor in metal
• Sensing range may decrease if the sensor is completely
embedded in metal. Especially for the non-threaded type
and the non-shielded type, keep the minimum distance
specified in the table below.
F
G
Metal
Note: With the non-shielded type, the sensing
range may vary depending on the
position of the nuts.
Model No.
GX-5SU(B)
GX-8MLU(B)
GX-12MLU(B)
GX-N12ML(B)
GX-18MLU(B)
GX-N18ML(B)
GX-30MLU(B)
GX-N30ML(B)
F (mm in) G (mm in)
ø12 ø0.472 3 0.118
ø24 ø0.945 12 0.472
ø50 ø1.969 15 0.591
ø75 ø2.953 25 0.984
ø105 ø4.134 30 1.181
Mutual interference
• When two or more sensors are installed in parallel or
face to face, keep the minimum separation distance
specified below to avoid mutual interference.
Face to face mounting
H
Parallel mounting
J
Model No. H (mm in) J (mm in)
GX-5SU(B) 19 0.748 14 0.551
GX-8MU(B)
GX-12MU(B)
GX-F12MU-J
GX-18MU(B)
GX-F18MU-J
GX-30MU(B)
GX-F30MU-J
GX-8MLU(B)
20 0.787 15 0.591
35 1.378 20 0.787
70 2.756 45 1.772
115 4.528 70 2.756
60 2.362 45 1.772
GX-12MLU(B) 145 5.709 95 3.740
GX-18MLU(B) 250 9.843 165 6.496
GX-30MLU(B) 350 13.780 250 9.843
GX-N12M(B) 25 0.984 15 0.591
GX-N18M(B) 50 1.969 35 1.378
GX-N30M(B) 90 3.543 55 2.165
GX-N12ML(B) 120 4.724 70 2.756
GX-N18ML(B) 180 7.087 125 4.921
GX-N30ML(B) 290 1.417 190 7.480