CYBLE-212006-01 Datasheet, PDF (9/39 Pages) Cypress Semiconductor – Module size: 15.00 mm × 23.00 mm × 2.00 mm

PRELIMINARY
CYBLE-212006-01
CYBLE-202007-01
CYBLE-202013-11
Digital and Analog Capabilities and Connections
Table 4 details the solder pad connection definitions and available functions for each connection pad. Table 4 lists the solder pads on
CYBLE-2X20XX-X1, the BLE device port-pin, and denotes whether the function shown is available for each solder pad. Each
connection is configurable for a single option shown with a ✓.
Table 4. Solder Pad Connection Definitions
Solder Pad Device
Number Port Pin
UART
SPI
I²C
TCPWM^[4,5]
CapSense
WCO
Out
ECO
Out
LCD
SWD
GPIO
1
GND
Ground Connection
2
XRES
External Reset Hardware Connection Input
3
P4.0^[6] ✓(SCB1_RTS) ✓(SCB1_MOSI)
✓(TCPWM0_P) ✓(C_MOD)
✓
✓
4
P3.7 ✓(SCB1_CTS)
✓(TCPWM) ✓(Sensor) _✓
✓
✓
5
P3.6 ✓(SCB1_RTS)
✓(TCPWM) ✓(Sensor)
✓
✓
6
P3.5 ✓(SCB1_TX)
✓(SCB1_SCL) ✓(TCPWM) ✓(Sensor)
✓
✓
7
P3.4 ✓(SCB1_RX)
✓(SCB1_SDA) ✓(TCPWM) ✓(Sensor)
✓
✓
8
V_REF
Reference Voltage Input (Optional)
9
P2.6
✓(TCPWM) ✓(Sensor)
✓
✓
10
P2.4
✓(TCPWM) ✓(Sensor)
✓
✓
11
P2.3
✓(TCPWM) ✓(Sensor) _✓
✓
✓
12
P2.2
✓(SCB0_SS3)
✓(TCPWM) ✓(Sensor)
✓
✓
13
P2.0
✓(SCB0_SS1)
✓(TCPWM) ✓(Sensor)
✓
✓
14
P1.7 ✓(SCB0_CTS) ✓(SCB0_SCLK
✓(TCPWM) ✓(Sensor)
✓
✓
15
P1.6 ✓(SCB0_RTS) ✓(SCB0_SS0)
✓(TCPWM) ✓(Sensor)
✓
✓
16
P1.5 ✓(SCB0_TX) ✓(SCB0_MISO) ✓(SCB0_SCL) ✓(TCPWM) ✓(Sensor)
✓
✓
17
P1.4 ✓(SCB0_RX) ✓(SCB0_MOSI) ✓(SCB0_SDA) ✓(TCPWM) ✓(Sensor)
✓
✓
18
P0.7 ✓(SCB0_CTS) ✓(SCB0_SCLK
✓(TCPWM) ✓(Sensor)
✓ ^{✓(SWDCLK)} ✓
19
P1.0
✓(TCPWM) ✓(Sensor)
✓
✓
20
P0.4 ✓(SCB0_RX) ✓(SCB0_MOSI) ✓(SCB0_SDA) ✓(TCPWM) ✓(Sensor)
✓✓
✓
21
P0.5 ✓(SCB0_TX) ✓(SCB0_MISO) ✓(SCB0_SCL) ✓(TCPWM) ✓(Sensor)
✓
✓
22
V_DD
23
P0.6 ✓(SCB0_RTS) ✓(SCB0_SS0)
24
GND^[7]
Digital Power Supply Input (1.8 to 5.5V)
✓(TCPWM) ✓(Sensor)
Ground Connection
✓ ^{✓(SWDIO)} ✓
25
GND
Ground Connection
26
GND
Ground Connection
27
GND
Ground Connection
28
V_DDR
Radio Power Supply (2V to 3.6V)
29
GND RF Ground Connection for use with CYBLE-202013-11 only; No Connect for CYBLE-212006-01 and CYBLE-202007-01
30
ANT RF Pin to External Antenna for use with CYBLE-202013-11 only; No Connect for CYBLE-212006-01 and CYBLE-202007-01
Notes
4. TCPWM: Timer, Counter, and Pulse Width Modulator. If supported, the pad can be configured to any of these peripheral functions.
5. TCPWM connections on ports 0, 1, 2, and 3 can be routed through the Digital Signal Interconnect (DSI) to any of the TCPWM blocks and can be either positive
or negative polarity. TCPWM connections on port 4 are direct and can only be used with the specified TCPWM block and polarity specified above.
6. When using the capacitive sensing functionality, Pad 3 (P4.0) must be connected to a C_MOD capacitor (located off of Cypress BLE Module). The value of this
capacitor is 2.2 nF and should be placed as close to the module as possible.
7. The main board needs to connect all GND connections (Pad 24/25/26/27) on the module to the common ground of the system.
8. If the I²S feature is used in the design, the I²S pins shall be dynamically routed to the appropriate available GPIO by PSoC Creator.
Document Number: 002-15631 Rev.*B
Page 9 of 39