CAT24FC64 Datasheet, PDF (2/10 Pages) Catalyst Semiconductor – 64K-Bit I2C Serial CMOS EEPROM

CAT24FC64
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias ................. –55°C to +125°C
Storage Temperature ....................... –65°C to +150°C
Voltage on Any Pin with
Respect to Ground⁽¹⁾ ........... –2.0V to +V_CC + 2.0V
V_CC with Respect to Ground ............... –2.0V to +7.0V
RELIABILITY CHARACTERISTICS
Package Power Dissipation
Capability (Ta = 25°C) ................................... 1.0W
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current⁽²⁾ ........................ 100mA
*COMMENT
Stresses above those listed under “Absolute Maximum Ratings” may
cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions
outside of those listed in the operational sections of this specification is not
implied. Exposure to any absolute maximum rating for extended periods
may affect device performance and reliability.
Symbol
Parameter
Reference Test Method
Min
Typ Max
Units
N_END(3)
TDR(3)
V_ZAP(3)
ILTH(3)(4)
Endurance
Data Retention
ESD Susceptibility
Latch-up
MIL-STD-883, Test Method 1033 1,000,000
MIL-STD-883, Test Method 1008 100
MIL-STD-883, Test Method 3015 4000
JEDEC Standard 17
100
Cycles/Byte
Years
Volts
mA
D.C. OPERATING CHARACTERISTICS
V_CC = +1.8V to +5.5V, unless otherwise specified.
Symbol Parameter
Test Conditions Min
Typ
Max Units
I_CC1
I_CC2
I_SB(5)
I_LI
I_LO
V_IL
V_IH
V_OL1
V_OL2
Power Supply Current - Read
Power Supply Current - Write
Standby Current
Input Leakage Current
Output Leakage Current
Input Low Voltage
f_SCL = 100 KHz
V_CC=5V
f_SCL = 400KHz
V_CC=5V
V_IN = GND or V_CC
V_CC=5V
V_IN = GND to V_CC
V_OUT = GND to V_CC
-0.5
Input High Voltage
Output Low Voltage (V_CC = +3.0V)
Output Low Voltage (V_CC = +1.8V)
I_OL = 3.0 mA
I_OL = 1.5 mA
V_CC x 0.7
1
mA
3
mA
1
µA
1
µA
1
µA
V_CC x 0.3 V
V_CC + 0.5 V
0.4
V
0.5
V
CAPACITANCE T_A = 25°C, f = 1.0 MHz, V_CC = 5V
Symbol Test
Conditions Min
Typ
Max
Units
C_I/O(3) Input/Output Capacitance (SDA)
V_I/O = 0V
8
pF
C_IN(3)
Input Capacitance (SCL, WP, A0, A1)
V_IN = 0V
6
pF
Z_WPL
WP Input Impedance
V_IN ≤ 0.5V
5
70
kΩ
Z_WPH
WP Input Impedance
V_IN>0.7VxV_CC 500
kΩ
Note:
(1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is V_CC +0.5V, which may overshoot to V_CC + 2.0V for periods of less than 20ns.
(2) Output shorted for no more than one second. No more than one output shorted at a time.
(3) This parameter is tested initially and after a design or process change that affects the parameter.
(4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to V_CC +1V.
(5) Standby current (I_SB ) = 10 µA max at extended temperature range.
Doc. No. 1046, Rev. G
2