SHC605 Datasheet, PDF (2/15 Pages) Burr-Brown (TI) – High-Speed Operational TRACK-AND-HOLD AMPLIFIER

SPECIFICATIONS
ELECTRICAL
At T_A = +25°C, ±V_S = ±5V, G = +1V/V, R_L = 100Ω, C_L = 5pF, and ECL Hold/Hold Inputs, unless otherwise noted.
SHC605AU
PARAMETER
CONDITION
TEMP RANGE
MIN
TYP
MAX
UNITS
DC INPUT PARAMETERS
Offset Voltage
Power Supply Rejection
Input Bias Current
Input Offset Current
Common-Mode Input Range
Common-Mode Rejection
Differential Input Impedance
Common-Mode Input Impedance
Open-Loop Voltage Gain
OUTPUT
Voltage Output
Current Output
Short Circuit Current
Output Resistance,
Closed-Loop: Track-Mode
Hold-Mode
V_S = ±4.5 to ±5.5V
V_CM = 0V
V_CM = 0V
V_CM = ±2VDC
V_O = ±2V, R_L = 100Ω
R_L = 50Ω
DC
DC
Full
+25°C
Full
Full
Full
Full
Full
Full
+25°C
Full
+25°C
Full
Full
Full
Full
±1
±7.5
mV
60
85
dB
15
50
µA
±0.2
±5
µA
±2.0
±2.5
V
80
dB
13||1
kΩ||pF
2||1
MΩ||pF
100
dB
±2.0
±2.5
V
±40
±80
mA
±40
±60
mA
±140
mA
0.0001
Ω
0.01
Ω
DIGITAL INPUTS/OUTPUTS
TTL Input Levels⁽¹⁾
V_IL
V_IH
Single-Ended ECL Input Levels ⁽²⁾
V_IL
V_IH
Common-Mode Input Voltages
Differential Input Voltages
Digital Input Currents
I_IL, Lock/Lock Inputs Only
I_IL, Hold/Hold Inputs Only
I_IH, Lock/Lock Inputs Only
I_IH, Hold/Hold Inputs Only
Threshold Voltage Output⁽³⁾
TTL⁽⁴⁾
ECL⁽⁵⁾
TRACK-MODE RESPONSE
Closed-Loop Bandwidth
Full Power Response
Slew Rate⁽⁶⁾
Acquisition Time to 1%⁽⁷⁾
0.1%
0.012%
0.012%
Input Voltage Noise
Input Bias Current Noise
Differential Gain
Differential Phase
Spurious Free Dynamic Range
(5MHz)
(10MHz)
Hold Input Only
Logic “LO”
Logic “HI”
Hold/Hold and Lock/Lock Inputs
Logic “LO”
Logic “HI”
Hold/Hold
Lock/Lock
Hold/Hold and Lock/Lock Inputs
ECL Logic “LO”, V_IL = –1.60V
ECL or TTL Logic “LO”
Logic “HI”, V_IH = –1.0V
–V_S = –5.2V
Gain = +1V/V
Gain = +2V/V
Gain = +5V/V
Gain = +10V/V
±1V Input, –3dB Output
G = +1, 2V Step
2V Step
2V Step
2V Step
4V Step
1MHz to 100MHz
1MHz to 100MHz
3.58MHz, V_O = 0 to 0.7Vp–p
3.58MHz, V_O = 0 to 0.7Vp–p
V_O = ±1V
V_O = ±1V
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
+25°C
+25°C
+25°C
+25°C
Full
+25°C
Full
Full
Full
Full
Full
0
+2.0
–1.80
–1.05
–3
–V_S
0.2
1.1
–1.40
100
140
120
1.5
200
75
20
10
32
200
200
15
23
30
40
2.5
2.5
0.005
0.005
83
73
+1.0
+5.0
–1.45
–0.80
+5
+3
5.0
5
–100
50
–10
1.9
–1.10
25
35
45
60
V
V
V
V
V
V
V
µA
µA
µA
µA
V
V
MHz
MHz
MHz
MHz
MHz
V/µs
V/µs
ns
ns
ns
ns
nV√Hz
pA/√Hz
%
Degrees
dBc
dBc
NOTE: (1) Select (Pin 10) connected to +V_S for TTL threshold voltage on Pin 11. (2) Select (Pin 10) connected to –V_S for ECL threshold voltage on Pin 11. (3) Output
voltage on pin 11. (4) Pin 10 (Select) connected to +V_S. (5) Pin 10 (Select) connected to –V_S. (6) Slew rate is rate of change from 10% to 90% of a 2V output step.
(7) Acquisition time includes hold-to-track delay switch time. (8) Hold noise is proportional to the time in the hold mode. For example, if the hold time is 25ns, the
accumulated noise is 10µVrms. (9) This is the maximum length of time the SHC605 can remain in the hold mode and still maintain a linear droop rate. (10) Select
(Pin 10) connected to +V_S.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN
assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject
to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize
or warrant any BURR-BROWN product for use in life support devices and/or systems.
®
SHC605
2