CC2530F32 Datasheet, PDF (5/31 Pages) Aplus Intergrated Circuits – A True System-on-Chip Solution for 2.4-GHz IEEE 802.15.4 and ZigBee Applications

CC2530F32, CC2530F64, CC2530F128, CC2530F256
www.ti.com .......................................................................................................................................................... SWRS081A – APRIL 2009 – REVISED APRIL 2009
GENERAL CHARACTERISTICS
Measured on Texas Instruments CC2530 EM reference design with T_A = 25°C and VDD = 3 V, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN TYP MAX UNIT
WAKE-UP AND TIMING
Power mode 1 → active
Digital regulator on, 16-MHz RCOSC and 32-MHz crystal
oscillator off. Start-up of 16-MHz RCOSC
4
µs
Power mode 2 or 3 → active
Digital regulator off, 16-MHz RCOSC and 32-MHz crystal
oscillator off. Start-up of regulator and 16-MHz RCOSC
0.1
ms
Active → TX or RX
Initially running on 16-MHz RCOSC, with 32-MHz XOSC
OFF
With 32-MHz XOSC initially on
0.5
ms
192 µs
RX/TX and TX/RX turnaround
192 µs
RADIO PART
RF frequency range
Programmable in 1-MHz steps, 5 MHz between channels
for compliance with [1]
2394
2507 MHz
Radio baud rate
As defined by [1]
250
kbps
Radio chip rate
As defined by [1]
2
MChip/s
RF RECEIVE SECTION
Measured on Texas Instruments CC2530 EM reference design with T_A = 25°C, VDD = 3 V, and f_c = 2440 MHz, unless
otherwise noted.
Boldface limits apply over the entire operating range, T_A = –40°C to 125°C, VDD = 2 V to 3.6 V, and f_c = 2394 MHz to
2507 MHz.
PARAMETER
Receiver sensitivity
Saturation (maximum input level)
Adjacent-channel rejection, 5-MHz
channel spacing
Adjacent-channel rejection, –5-MHz
channel spacing
Alternate-channel rejection, 10-MHz
channel spacing
Alternate-channel rejection, –10-MHz
channel spacing
Channel rejection
≥ 20 MHz
≤ –20 MHz
Co-channel rejection
Blocking/desensitization
5 MHz from band edge
10 MHz from band edge
20 MHz from band edge
50 MHz from band edge
–5 MHz from band edge
–10 MHz from band edge
–20 MHz from band edge
–50 MHz from band edge
TEST CONDITIONS
PER = 1%, as specified by [1]
[1] requires –85 dBm
PER = 1%, as specified by [1]
[1] requires –20 dBm
Wanted signal –82 dBm, adjacent modulated channel at
5 MHz, PER = 1 %, as specified by [1].
[1] requires 0 dB
Wanted signal –82 dBm, adjacent modulated channel at
–5 MHz, PER = 1 %, as specified by [1].
[1] requires 0 dB
Wanted signal –82 dBm, adjacent modulated channel at
10 MHz, PER = 1%, as specified by [1]
[1] requires 30 dB
Wanted signal –82 dBm, adjacent modulated channel at
–10 MHz, PER = 1 %, as specified by [1]
[1] requires 30 dB
Wanted signal at –82 dBm. Undesired signal is an IEEE
802.15.4 modulated channel, stepped through all channels
from 2405 to 2480 MHz. Signal level for PER = 1%.
Wanted signal at –82 dBm. Undesired signal is 802.15.4
modulated at the same frequency as the desired signal. Signal
level for PER = 1%.
MIN TYP MAX
–97 –92
–88
UNIT
dBm
10
dBm
49
dB
49
dB
57
dB
57
dB
57
dB
57
–3
dB
Wanted signal 3 dB above the sensitivity level, CW jammer,
PER = 1%. Measured according to EN 300 440 class 2.
–33
–33
–32
–31
dBm
–35
–35
–34
–34
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): CC2530F32 CC2530F64 CC2530F128 CC2530F256