SW06 Datasheet, PDF (3/12 Pages) Analog Devices – Quad SPST JFET Analog Switch

SW06
ELECTRICAL CHARACTERISTICS (@ V+ = +15 V, V– = –15 V, –55؇C ≤ TA ≤ +125؇C for SW06BQ, –40؇C ≤ TA ≤ +85؇C for
SW06FQ and –40؇C ≤ T_A ≤ +85؇C for SW06GP/GS, unless otherwise noted)
Parameter
Symbol
Conditions
SW06B
SW06F
SW06G
Min Typ Max Min Typ Max Min Typ Max Units
TEMPERATURE RANGE
T_A
Operating
–55
+125 –25
+85 0
70 °C
“ON” RESISTANCE
R_ON
∆R_ON MATCH BETWEEN SWITCHES R_ON Match
ANALOG VOLTAGE RANGE
V_A
V_S = 0 V, I_S = 1.0 mA
V_S = ± 10 V, I_S = 1.0 mA
V_S = 0 V, I_S = 100 µA¹
I_S = 1.0 mA²
I_S = 1.0 mA²
75 110
80 110
75 125
80 125
75 175 Ω
80 175
6 20
6 25
10
%
+10 +11
+10 +11
+10 +11
V
–10 –15
–10 –15
–10 –15
ANALOG CURRENT RANGE
∆R_ON WITH APPLIED VOLTAGE
I_A
∆R_ON
V_S = ± 10 V
7 12
–10 V ≤ V_S ≤ 10 V, I_S = 1.0 mA
10
5 11
12
11
mA
15
%
SOURCE CURRENT IN
“OFF” CONDITION
V_S = 10 V, V_D = –10 V
I_S(OFF)
T_A = Max Operating Temp^{3, 9}
60
30
60 nA
DRAIN CURRENT IN
“OFF” CONDITION
V_S = 10 V, V_D = –10 V
I_D(OFF)
T_A = Max Operating Temp^{3, 9}
60
30
60 nA
LEAKAGE CURRENT IN
“ON” CONDITION
LOGICAL “1” INPUT CURRENT
LOGICAL “0” INPUT CURRENT
TURN-ON TIME
I_S(ON)+
I_D(ON)
I_INH
I_INL
t_ON
V_S = V_D = ± 10 V
T_A = Max Operating Temp^{3, 9}
V_IN = 2.0 V to 15.0 V⁵
V_IN = 0.8 V
See Switching Time
Test Circuit^{4, 8}
100
10
4 10
440 900
30
10
4 10
500 900
TURN-OFF TIME
t_OFF
See Switching Time
Test Circuit^{4, 8}
300 500
330 500
BREAK-BEFORE-MAKE TIME
POSITIVE SUPPLY CURRENT
t_ON–t_OFF
I+
Note 7
All Channels “OFF,”
DIS = “0”³
70
9.0
70
13.5
NEGATIVE SUPPLY CURRENT
I–
All Channels “OFF,”
DIS = “0”³
7.5
10.5
GROUND CURRENT
I_G
All Channels “ON” or
“OFF”³
6.0
7.5
NOTES
1_{VS = 0 V, IS = 100 µA. Specified as a percentage of RAVERAGE where: RAVERAGE =}
R_ON1
+ R_ON2
+ R_{ON 3}
4
+ R_{ON 4}
.
2_{Guaranteed by RON and leakage tests. For normal operation maximum analog signal voltages should be restricted to less than (V+) –4 V.}
3_{Switch being tested ON or OFF as indicated, VINH = 2.0 V or VINL = 0.8 V, per logic truth table.}
4_{Also applies to disable pin.}
5_{Current tested at VIN = 2.0 V. This is worst case condition.}
6_{Sample tested.}
7_{Switch is guaranteed by design to provide break-before-make operation.}
8_{Guaranteed by design.}
9_{Parameter tested only at TA = +125°C for military grade device.}
Specifications subject to change without notice.
60 nA
15 µA
5 15 µA
1000 ns
500 ns
50
ns
13.5 mA
10.5 mA
7.5 mA
REV. A
–3–