X9119 Datasheet, PDF (12/22 Pages) Xilinx, Inc – Single Digitally-Controlled (XDCP ™ ) Potentiometer

X9119 – Preliminary Information
ABSOLUTE MAXIMUM RATINGS
Temperature under bias.................... –65°C to +135°C
Storage temperature......................... –65°C to +150°C
Voltage on SCL, SDA, or any address input
with respect to V_SS ................................. –1V to +7V
∆V = | (VH–VL) | ......................................................5V
Lead temperature (soldering, 10 seconds) ........ 300°C
I_W (10 seconds) ..................................................±6mA
COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; the functional operation of
the device (at these or any other conditions above
those listed in the operational sections of this
specification) is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Temp
Commercial
Industrial
Min.
0°C
–40°C
Max.
+70°C
+85°C
Device
X9119
X9119-2.7
Supply Voltage (V_CC) Limits⁽⁴⁾
5V ±10%
2.7V to 5.5V
ANALOG CHARACTERISTICS (Over recommended industrial (2.7V) operation conditions unless otherwise stated.)
Symbol
R_TOTAL
I_W
R_W
R_W
V_TERM
C_H/C_L/C_W
Parameter
End to End Resistance
End to End Resistance Tolerance
Power Rating
Wiper Current
Wiper Resistance
Wiper Resistance
Voltage on any R_H or R_L Pin
Noise
Resolution
Absolute Linearity⁽¹⁾
Relative Linearity⁽²⁾
Temperature Coefficient of R_TOTAL
Ratiometric Temp. Coefficient
Potentiometer Capacitancies
Min.
V_SS
Limits
Typ. Max.
100
±20
50
±3
150 500
40
100
5
-120
0.1
±1
Units
kΩ
%
mW
mA
Ω
Ω
V
dBV
%
MI⁽³⁾
±1.5
±0.5
MI⁽³⁾
MI⁽³⁾
±1
MI⁽³⁾
±300
ppm/°C
20 ppm/°C
10/10/25
pF
Test Conditions
25°C, each pot
Wiper Current = ± 3mA, V_CC = 3V
I_W = ± 3mA, V_CC = 5V
V_SS = 0V
Ref: 1V
R_w(n)(actual) – R_{w(n)(expected)},
where n=8 to 1006
R_w(n)(actual) – R_{w(n)(expected)}⁽⁵⁾
R_{w(m + 1)} – [R_w(m) + MI], where
m=8 to 1006
R_{w(m + 1)} – [R_w(m) + MI]⁽⁵⁾
See Macro model
Notes: (1) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used
as a potentiometer.
(2) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a
potentiometer. It is a measure of the error in step size.
(3) MI = RTOT / 1023 or (R_H – R_L) / 1023, single pot
(4) n = 0, 1, 2, …,1023; m =0, 1, 2, …, 1022.
(5) ESD Rating on RH, RL, RW pins is 1.5KV (HBM, 1.0µA leakage maximum), ESD rating on all other pins is 2.0kV.
REV 1.1.11 3/12/02
www.xicor.com
Characteristics subject to change without notice. 12 of 22