X9241 Datasheet, PDF (9/16 Pages) Xicor Inc. – Quad E2POT™ Nonvolatile Digital Potentiometer

X9241
ABSOLUTE MAXIMUM RATINGS*
Temperature under Bias .................. –65°C to +135°C
Storage Temperature ....................... –65°C to +150°C
Voltage on SCK, SCL or any Address Input
with Respect to V_SS ................................... –1V to +7V
Voltage on any V_H or V_L Referenced to V_SS ......... ±8V
∆V = |V_H–V_L| ......................................................... 16V
Lead Temperature (Soldering, 10 seconds)...... 300°C
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation of
the device at these or any other conditions above those
indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Temperature
Min.
Max.
Supply Voltage
Limits
Commercial
0°C
+70°C
X9241
5V ±10%
Industrial
–40°C
+85°C
3864 PGM T04.1
Military
–55°C
+125°C
3864 PGM T03
ANALOG CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)
Limits
Symbol
Parameter
Min. Typ.
Max. Units
Test Conditions
R_TOTAL End to End Resistance
–20
Power Rating
+20
%
50
mW 25°C, each pot
I_W
R_W
V_TERM
Wiper Current
Wiper Resistance
Voltage on any V_H or
or V_L Pin
Noise
–1
+1
mA
40
100
Ω
Wiper Current = ± 1mA
–5
+5
V
≤120
dB/
Ref: 1V
Resolution ⁽⁴⁾
1.6
0.4
%
Absolute Linearity ⁽¹⁾
Relative Linearity ⁽²⁾
Temperature Coefficient
–1
–0.2
±300
+1
+0.2
MI⁽³⁾
MI⁽³⁾
ppm/°C
V_w(n)(actual) – V_{w(n)(expected)}
V_{w(n + 1)} – [V_{w(n) + MI}]
3864 PGM T05.2
D.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)
Limits
Symbol
Parameter
Min. Typ.
Max. Units
Test Conditions
l_CC Supply Current (Active)
3
mA f_SCL = 100KHz, SDA = Open,
Other Inputs = V_SS
I_SB V_CC Current (Standby)
200
500
µA SCL=SDA=V_CC, Addr. = V_SS
I_LI Input Leakage Current
10
µA
V_IN = V_SS to V_CC
I_LO Output Leakage Current
10
µA
V_OUT = V_SS to V_CC
V_IH Input HIGH Voltage
2
V_CC + 1
V
V_IL Input LOW Voltage
–1
0.8
V
V_OL Output LOW Voltage
0.4
V
I_OL = 3mA
Notes: (1) Absolute Linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper
3864 PGM T06.3
position when used as a potentiometer.
(2) Relative Linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a
potentiometer. It is a measure of the error in step size.
(3) MI = RTOT/63 or (V_H – V_L)/63, single pot
(4) Max. = all four arrays cascaded together, Typical = individual array resolutions.
9