X9250 Datasheet, PDF (2/21 Pages) Xicor Inc. – Quad Digitally Controlled Potentiometers (XDCP)

X9250
PIN DESCRIPTIONS
Serial Output (SO)
SO is a serial data output pin. During a read cycle,
data is shifted out on this pin. Data is clocked out by
the falling edge of the serial clock.
Serial Input
SI is the serial data input pin. All opcodes, byte
addresses and data to be written to the pots and pot
registers are input on this pin. Data is latched by the
rising edge of the serial clock.
Serial Clock (SCK)
The SCK input is used to clock data into and out of the
X9250.
Chip Select (CS)
When CS is HIGH, the X9250 is deselected and the
SO pin is at high impedance, and (unless an internal
write cycle is underway) the device will be in the
standby state. CS LOW enables the X9250, placing it
in the active power mode. It should be noted that after
a power-up, a HIGH to LOW transition on CS is
required prior to the start of any operation.
Hold (HOLD)
HOLD is used in conjunction with the CS pin to select
the device. Once the part is selected and a serial
sequence is underway, HOLD may be used to pause
the serial communication with the controller without
resetting the serial sequence. To pause, HOLD must
be brought LOW while SCK is LOW. To resume
communication, HOLD is brought HIGH, again while
SCK is LOW. If the pause feature is not used, HOLD
should be held HIGH at all times.
Device Address (A₀–A₁)
The address inputs are used to set the least significant
2 bits of the 8-bit slave address. A match in the slave
address serial data stream must be made with the
address input in order to initiate communication with
the X9250. A maximum of 4 devices may occupy the
SPI serial bus.
Potentiometer Pins
V_H/R_H (V_H0/R_H0–V_H3/R_H3), V_L/R_L (V_L0/R_L0–V_L3/R_L3)
The R_H and R_L pins are equivalent to the terminal
connections on a mechanical potentiometer.
V_W/R_W (V_W0/R_W0–V_W3/R_W3)
The wiper pins are equivalent to the wiper terminal of
a mechanical potentiometer.
Hardware Write Protect Input (WP)
The WP pin when LOW prevents nonvolatile writes to
the Data Registers.
Analog Supplies (V+, V-)
The analog supplies V+, V- are the supply voltages for
the XDCP analog section.
PIN CONFIGURATION
S0
A0
V_W3/R_W3
V_H3/R_H3
V_L3/R_L3
V+
V_CC
V_L0/R_L0
V_H0/R_H0
V_W0/R_W0
CS
WP
SOIC/TSSOP
1
24
2
23
3
22
4
21
5
20
6
19
X9250
7
18
8
17
9
16
10
15
11
14
12
13
HOLD
SCK
V_L2/R_L2
V_H2/R_L2
V_W2/R_W2
V–
V_SS
V_W1/R_W1
V_H1/R_H1
V_L1/R_L1
A1
SI
CSP
12 3 4
A ^{RW0 CS A1 RL1}
RL0 WP SI ^RW1
B
VCC RH0 RH1 VSS
C
V+ RH3 RH2 V-
D
R_L3 SO HOLD R_W2
E
RW3 A0 SCK RL2
F
Top View–Bumps Down
REV 1.1.5 1/31/03
www.xicor.com
Characteristics subject to change without notice. 2 of 21