PSPRL0801D Datasheet, PDF (2/6 Pages) Wall Industries,Inc. – AC/DC Switching Power Supply

Rev. A
PSPRL0801D Series
Up to 240 Watts
Dual Output, Active PFC
AC/DC Switching Power Supply
SPECIFICATIONS: PSPRL0801D Series
All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
We reserve the right to change specifications based on technological advances.
INPUT SPECIFICATIONS
Input Voltage
Input Frequency
Input Current
Inrush Current
Remote ON/OFF
PFC
OUTPUT SPECIFICATIONS
Output Voltage
Output Power (See Note 2)
Output Adjustability
Regulation
Output Current
Ripple & Noise (See Note 3)
Transient Response
Hold-Up Time
Overshoot
Turn On Delay
PROTECTION
Over Voltage Protection
Short Circuit Protection
Over Temperature Protection
Over Power Protection
Input Fusing Protection
GENERAL SPECIFICATIONS
Switching Frequency
Efficiency
Withstand Voltage
Leakage Current
Burn In
Power Good
Power Supply On
Grounding Test
Fan Drive
Fan Fail (FF) Alarm
90 ~ 264VAC full range
47 to 63Hz
5A @ 90VAC
35A max. @ 115VAC and 70A max. @ 230VAC; cold start.
Designated as INH on pin 4 of CN3. Requires a low signal to inhibit output.
Power factor correction pass EN61000-3-2 Class D.
See Table
240 Watts max. with 25CFM airflow.
Output adjustable ±5% minimum.
±5%
See Table
1% (peak to peak)
Returns to within 1% in less than 2.5ms for a 50% load change and the peak transient does not exceed 5%.
16ms min. at 80% of full load and 120VAC
Turn-on & off overshoot < 5% over nominal voltage.
1 second maximum at 120VAC.
Unit latching down when output exceeds 130% and recycle AC input to reset.
Trips without damage and auto-recovery.
Unit protected against excessive operating ambient 85°C±5°C; automatic recovery.
Foldback mode 110~140%; auto-recovery.
One F5A/350V fuse inserted into primary.
70KHz fixed frequency.
70% typical (Measured at 230VAC and full load).
1500VAC input line to chassis (10mA DC cut-off current). 3000VAC primary to secondary windings; 1500VAC
primary to core. All for 3 sec.
3.5mA @ 240VAC
45 ±5°C for 1 hour @ 230VAC with full load.
Designated as PG on CN3 and TTL high 100-500ms after DC regulation. It goes low at least 1ms before loss of
regulation and has ability to sink 100mA.
Green LED designated as LED1 on the PCB.
Apply 25A from ground pin of the three prong plug to the far most earth. Max. allowable resistance is 0.1Ω.
12VDC/300mA offering to drive an external fan.
Designated as FF on pin 3 of CN3 is an open collector output rated for 28VDC/5mA sink current maximum; it will
go high when a fan failure is detected.
ENVIRONMENTAL SPECIFICATIONS
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Vibration
Cooling (See Note 2)
MTBF
PHYSICAL SPECIFICATIONS
Weight
Dimensions (L x W x H)
SAFETY
Emissions
Safety Regulations
0°C to +70°C ambient, de-rating at 2.5% per degree from 50°C to 70°C.
-20°C to +85°C
5% to 90% RH, non-condensing
5% to 95% RH, non-condensing
5 ~ 50Hz, acceleration ±7.35 m/(s x s) on X, Y, and Z axis.
U Type (U-Chassis): 240W max with 25CFM forced airflow or 120W under convection cooling.
C Type (U-Chassis with top cover): 240W max with 25CFM forced airflow or 120W under convection cooling.
E Type (Enclosed with rear side built-in fan): 240W max.
F Type (Enclosed with top built-in fan): 240W max.
100,000 hours (according to MIL-HBK-217F) at 30°C.
U Type (U-Chassis): 17.64oz (500g)
C Type (U-Chassis with top cover): 19.40oz (550g)
E Type (Enclosed with rear side built-in fan): 22.93oz (650g)
F Type (Enclosed with top built-in fan): 21.16oz (600g)
U Type (U-Chassis): 5 x 3.2 x 1.5 inches (127.00 x 81.28 x 38.10 mm)
C Type (U-Chassis with top cover): 5 x 3.2 x 1.66 inches (127.00 x 81.28 x 42.10 mm)
E Type (Enclosed with rear side built-in fan): 6.5 x 3.2 x 1.6 inches (165.10 x 81.28 x 40.64 mm)
F Type (Enclosed with top built-in fan): 5 x 3.2 x 2 inches (127.00 x 81.28 x 50.8 mm)
FCC Part 15, CISPR 22 class B, conducted.
Approved to UL60950-1, TUV EN60950-1, CE Mark EN55022 & EN55024 regulations and CB.
10/01/2010
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax [phone]
Page 2 of 6