PR02000201008JA100 Datasheet, PDF (14/16 Pages) Vishay Siliconix – Power Metal Film Leaded Resistors

www.vishay.com
PR01/02/03
Vishay BCcomponents
TEST PROCEDURES AND REQUIREMENTS
IEC
60115-1
CLAUSE
IEC
60068-2-
TEST
METHOD
TEST
PROCEDURE
4.7
Voltage proof on
insulation
Maximum voltage U_RMS = 500 V
during 1 min; metal block method
4.16
Robustness of
terminations:
4.16.2
21 (Ua1) Tensile all samples
Load 10 N; 10 s
4.16.3
4.16.4
21 (Ub)
21 (Uc)
Bending half
number of samples
Torsion other half
of samples
Load 5 N; 4 x 90°
3 x 360° in opposite directions
4.20
29 (Eb)
Bump
3 x 1500 bumps in three directions; 40 g
4.22
6 (Fc)
Vibration
Frequency 10 Hz to 500 Hz;
displacement 1.5 mm or acceleration 10 g;
three directions; total 6 h (3 x 2 h)
4.19
14 (Na)
Rapid change of
temperature
30 min at LCT and
30 min at UCT; 5 cycles
4.23
4.23.2
4.23.3
4.23.4
4.23.5
4.23.6
4.24
4.25.1
4.8
4.6.1.1
2 (Ba)
30 (Db)
1 (Aa)
13 (M)
30 (Db)
78 (Cab)
Climatic sequence:
Dry heat
Damp heat
(accelerated)
1^st cycle
Cold
Low air pressure
Damp heat
(accelerated)
remaining cycles
Damp heat
(steady state)
Endurance
(at 70 °C)
Temperature
coefficient
Insulation resistance
16 h; 155 °C
24 h; 55 °C; 90 % to 100 % RH
2 h; - 55 °C
2 h; 8.5 kPa; 15 °C to 35 °C
5 days; 55 °C; 95 % to 100 % RH
56 days; 40 °C; 90 % to 95 % RH;
loaded with 0.01 P₇₀ (Steps: 0 V to 100 V)
1000 h; loaded with P₇₀ or U_max.;
1.5 h ON and 0.5 h OFF
Between - 55 °C and + 155 °C
Maximum voltage (DC) after 1 min;
metal block method
REQUIREMENTS
No breakdown or flashover
Number of failures:
< 1 x 10^-6
Number of failures:
< 1 x 10^-6
No damage
R_max.: ± (0.5 % R + 0.05 )
No damage
R_max.: ± (0.5 % R + 0.05 )
No damage
R_max.: ± (0.5 % R + 0.05 )
No visual damage
PR01: R_max.: ± (1 % R + 0.05 
PR02: R_max.: ± (1 % R + 0.05 
PR03: R_max.: ± (2 % R + 0.05 
R_{ins min.}: 10³ M
R_max.: ± (1.5 % R + 0.1 )
R_{ins min.}: 1000 M
R_max.: ± (3 % R + 0.1 )
R_max.: ± (5 % R + 0.1 )
 ± 250 ppm/K
R_{ins min.}: 10⁴ M
Revision: 24-Jun-13
14
Document Number: 28729
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000