15536 Datasheet, PDF (12/13 Pages) Vishay Siliconix – Solid Tantalum Chip Capacitors

Solid Tantalum Chip Capacitors
TANTAMOUNT® Conformal Coated,
Maximum CV
595D
Vishay Sprague
TAPE AND REEL PACKAGING in inches [millimeters]
Note: Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
T2
Max.
0.024
[0.600]
Max.
Deformation
Between
Embossments
0.059 + 0.004 - 0.0
[1.5 + 0.10 - 0.0]
0.157 ± 0.004
[4.0 ± 0.10]
10 Pitches Cumulative
Tolerance on Tape
± 0.008 [0.200]
Embossment
0.079 ± 0.002
[2.0 ± 0.05]
0.069 ± 0.004
[1.75 ± 0.10]
B1Max.
(Note 6)
K0
Top
Cover
Tape
0.004 [0.10]
For Tape Feeder _Max.
Reference only
including draft.
Concentric around B0
(Note 5)
Top
Cover
Tape
A0
B0
Center Lines
P1
of Cavity
USER DIRECTION OF FEED
0.030 [0.75]
Min. (Note 3)
F
W
0.030 [0.75]
Min. (Note 4)
20˚
Maximum
Component
Rotation
(Side or Front Sectional Vie w )
D1Min. For Components
0.079 x 0.047 [2.0 x 1.2] and Large.r
Maximum (Note 5)
Cavity Size
(Note 1)
Cathode (-)
Anode (+)
DIRECTION OF FEED
20˚ Maximum
Component Rotation
Typical
Component
B0
Cavity
Center Line
A0
(Top View)
Typical
Component
Center Line
3.937 [100.0]
0.039 [1.0]
Max.
Tape
0.039 [1.0]
Max.
0.9843 [250.0]
Camber
(Top View)
Allowable Camber to be 0.039/3.937 [1/100]
Non-Cumulative Over 9.843 [250.0]
Tape and Reel Specifications: All case sizes are
available on plastic embossed tape per EIA-481-1.
Tape reeling per IEC 286-3 is also available. Standard
reel diameter is 7" [178mm]. 13" [330mm] reels are
available and recommended as the most cost effective
packaging method.
The most efficient packaging quantities are full reel
increments on a given reel diameter. The quantities
shown allow for the sealed empty pockets required to
be in conformance with EIA-481-1. Reel size and
packaging orientation must be specified in the Vishay
Sprague part number.
Tape Size
8 mm
B₁ (Max.)
(Note 6)
0.179
[4.55]
D₁ (Min.)
(Note 5)
0.039
[1.0]
F
P₁
0.138 ± 0.002 0.157 ± 0.004
[3.5 ± 0.05] [4.0 ± 0.10]
R (Min.)
(Note 2)
0.984
[25.0]
T₂ (Max.)
0.098
[2.5]
W
0.315 + 0.012 - 0.004
[8.0 + 0.3 - 0.1]
A₀B₀K₀
12 mm
0.323
[8.2]
0.059
[1.5]
0.217 ± 0.002 0.157 ± 0.004
[5.5 ± 0.05] [4.0 ± 0.10]
1.181
[30.0]
0.256
[6.5]
0.472 ± 0.012
[12.0 ± 0.30]
(Note 1)
12 mm
Double Pitch
0.323
[8.2]
0.059
[1.5]
0.453 ± 0.004 0.315 ± 0.004
[11.5 ± 0.03] [8.0 ± 0.10]
1.181
[30.0]
0.256
[6.5]
0.945 ± 0.012
[24.0 ± 0.30]
Notes:
1.
A₀B₀K₀ are determined by the maximum dimensions to the
ends of the terminals extending from the component body
and/or the body dimensions of the component. The
clearance between the ends of the terminals or body of the
component to the sides and depth of the cavity (A₀B₀K₀)
must be within 0.002" [0.05 mm] minimum and 0.020" [0.50
mm] maximum. The clearance allowed must also prevent
rotation of the component within the cavity of not more than
20 degrees.
2.
Tape with components shall pass around radius "R" without
damage. The minimum trailer length may require additional
length to provide R minimum for 12 mm embossed tape for
reels with hub diameters approaching N minimum.
3.
This dimension is the flat area from the edge of the sprocket
hole to either the outward deformation of the carrier tape
between the embossed cavities or to the edge of the cavity
whichever is less.
4.
This dimension is the flat area from the edge of the carrier
tape opposite the sprocket holes to either the outward
deformation of the carrier tape between the embossed
cavity or to the edge of the cavity whichever is less.
5.
The embossment hole location shall be measured from the
sprocket hole controlling the location of the embossment.
Dimensions of embossment location and hole location shall
be applied independent of each other.
6.
B1 dimension is a reference dimension for tape feeder
clearance only.
Document Number: 40007
Revision: 16-Dec-05
For technical questions, contact: [e-mail]
www.vishay.com
12