C0402C0G1C010C020BC Datasheet, PDF (19/35 Pages) TDK Electronics – Commercial Grade ( General (Up to 50V) )

BR25G128-3
Datasheet
I/O Peripheral Circuits
In order to realize stable high speed operations, pay attention to the following input / output pin conditions.
Input pin pull up, pull down resistance
When to attach pull up, pull down resistance to EEPROM input pin, select an appropriate value for the microcontroller V_OL,
I_OL with considering V_IL characteristics of this IC.
1. Pull Up Resistance
Vcc－VOLM
R_PU ≥
IOLM
･･･①
Microcontroller IOLM
RPU
VOLM
EEPROM
VILE
“L” output
“L” input
Figure 49. Pull up resistance
VOLM ≤ 　VILM _{･･･②}
Example) When Vcc=5V, V_ILE=1.5V, V_OLM=0.4V, I_OLM=2mA,
from the equation ①,
R_PU
≥
5‐0.4
2 ×10^‐3
∴ R_PU ≥ 2.3[kΩ]
With the value of Rpu to satisfy the above equation, V_OLM
becomes 0.4V or lower, and with V_ILE (=1.5V), the equation ② is
also satisfied.
・V_ILE :EEPROM V_IL specifications
・V_OLM :Microcontroller V_OL specifications
・I_OLM :Microcontroller I_OL specifications
And, in order to prevent malfunction or erroneous write at power ON/OFF, be sure to make CSB pull up.
2. Pull Down Resistance
VOHM
R_PD ≥ _IOHM
･･･③
Microcontroller
VOHM
“H” output
IOHM
RPD
EEPROM
VIHE
“H” input
Figure 50. Pull down resistance
VOLM ≤ 　VIHM ･･･④
Example) When V_CC=5V, V_OHM=V_CC-0.5V, I_OHM＝0.4mA,
V_IHE=V_CC×0.7V, from the equation③,
R_PD
≥
5‐0.5
0.4 ×10^‐3
∴R_PD ≥ 11.3[kΩ]
Further, by amplitude V_IHE, V_ILE of signal input to EEPROM, operation speed changes. By inputting Vcc/GND level
amplitude of signal, more stable high speed operations can be realized. On the contrary, when amplitude of 0.8VCC /
0.2Vcc is input, operation speed becomes slow. ^(Note1)
In order to realize more stable high speed operation, it is recommended to make the values of R_PU, R_PD as large as
possible, and make the amplitude of signal input to EEPROM close to the amplitude of VCC / GND level.
(Note1) In this case, guaranteed value of operating timing is guaranteed.
3. SO Load Capacity Condition
Load capacity of SO output pin affects upon delay characteristic of SO output (Data output delay time, time from HOLDB
to High-Z, Output rise time, Output fall time.). In order to make output delay characteristic into better, make SO load
capacity small.
EEPROM
SO
CL
Figure 51. SO load capacity
4. Other cautions
Make the each wire length from the microcontroller to EEPROM input pin same length, in order to prevent setup / hold
violation to EEPROM, owing to difference of wire length of each input.
www.rohm.com
©2014 ROHM Co., Ltd. All rights reserved.
TSZ22111ï½¥15ï½¥001
19/32
TSZ02201-0R2R0G100670-1-2
19.Mar.2014 Rev.001