LP3941 Datasheet, PDF (9/34 Pages) Texas Instruments – Cellular Phone Power Management Unit

V_O4 LDO Electrical Characteristics
Unless otherwise noted, V_IN = V_BATT = 3.6V. Typical values and limits appearing in normal type apply for T_J = 25°C. Limits appearing
in boldface type apply over the entire junction temperature range for operation, −40 to +125°C. (Note 2, Note 8, Note 9)
Symbol
Parameter
Condition
Min
Typ
Max
Units
V_OUT
Output Voltage
Accuracy
V_OUT
Range
Programmable Output Voltage
Range
1 mA ≤ I_OUT ≤ 50 mA, V_OUT = 2.2V
3.0V ≤ V_BATT = V_IN ≤ 5.5V
0 µA ≤ I_OUT ≤ 50 mA
Programming Resolution = 100 mV
−3
±1.0
+3
%
1.5
3.0
3.0
V
I_OUT
Output Current
V_IN–V_OUT
ΔV_OUT
Output Current Limit
Dropout Voltage
Line Regulation
e_N
PSRR
Load Regulation
Output Noise Voltage
Power Supply Ripple
Rejection Ratio
(V_OUT + 0.25V, 3.0V)_MAX ≤ V_BATT
V_BATT = V_IN ≤ 5.5V
V_OUT = 0V
I_OUT = 25 mA
(V_OUT + 0.25V, 3.0V)_MAX ≤ V_BATT
V_BATT = V_IN ≤ 5.5V, I_OUT = 25 mA
V_IN = 3.6V, 1 mA ≤ I_OUT ≤ 50 mA
10 Hz ≤ f ≤ 100 kHz,
C_OUT = 1.0 µF
f = 217 Hz, C_OUT = 1.0 µF
50
mA
140
7
90
mV
3
mV
4
31
27
µV_RMS
56
dB
I_GND
C_OUT
Ground Current
Output Capacitance
Output Capacitor ESR
I_OUT = 100 µA
0 µA ≤ I_OUT ≤ 50 mA
30
µA
1
20
µF
5
500
mΩ
t_START-UP Start-Up Time from Shutdown
C_OUT = 1.0 µF, I_OUT = 50 mA (Note 10)
60
µs
V_O5 LDO Electrical Characteristics
Unless otherwise noted, V_IN = V_BATT = 3.6V. Typical values and limits appearing in normal type apply for T_J = 25°C. Limits appearing
in boldface type apply over the entire junction temperature range for operation, −40 to +125°C. (Note 2, Note 8, Note 9)
Symbol
Parameter
Condition
Min
V_OUT
Output Voltage
Accuracy
1 mA ≤ I_OUT ≤ 50 mA, V_OUT = 2.2V
−3
3.0V ≤ V_BATT = V_IN ≤ 5.5V
V_OUT
Range
Programmable Output Voltage
Range
0 µA ≤ I_OUT ≤ 50 mA
Programming Resolution = 100 mV
2.5
I_OUT
Output Current
V_IN–V_OUT
ΔV_OUT
Output Current Limit
Dropout Voltage
Line Regulation
e_N
PSRR
Load Regulation
Output Noise Voltage
Power Supply Ripple
Rejection Ratio
(V_OUT + 0.25V, 3.0V)_MAX ≤ V_BATT
V_BATT = V_IN ≤ 5.5V
V_OUT = 0V
I_OUT = 25 mA
(V_OUT + 0.25V, 3.0V)_MAX ≤ V_BATT
V_BATT = V_IN ≤ 5.5V, I_OUT = 25 mA
V_IN = 3.6V, 1 mA ≤ I_OUT ≤ 50 mA
10 Hz ≤ f ≤ 100 kHz,
C_OUT = 1.0 µF
f = 217 Hz, C_OUT = 1.0 µF
I_GND
Ground Current
I_OUT = 100 µA
C_OUT
Output Capacitance
0 µA ≤ I_OUT ≤ 50 mA
1
Output Capacitor ESR
5
t_START-UP Start-Up Time from Shutdown
C_OUT = 1.0 µF, I_OUT = 50 mA (Note 10)
Typ
±1.0
2.8
160
7
3
4
27
56
30
60
Max
Units
+3
%
3.2
V
50
mA
90
mV
mV
31
µV_RMS
dB
µA
20
µF
500
mΩ
µs
Note: This LDO will be ON after start-up by default.
Note: This LDO has an external active high enable pin, V_O5-EN as well as the internal register enable bit. The LDO is on if either of these is “1” (OR-function).
The enable bit is “1” by default and can be disabled via the register file.
www.ti.com
8
200945 Version 4 Revision 2 Print Date/Time: 2011/10/25 13:09:13