LP3941 Datasheet, PDF (8/34 Pages) Texas Instruments – Cellular Phone Power Management Unit

V_O2 LDO Electrical Characteristics
Unless otherwise noted, V_IN = V_BATT = 3.6V. Typical values and limits appearing in normal type apply for T_J = 25°C. Limits appearing
in boldface type apply over the entire junction temperature range for operation, −40 to +125°C. (Note 2, Note 8, Note 9)
Symbol
Parameter
Condition
Min
Typ
Max
Units
V_OUT
Output Voltage
Accuracy
1 mA ≤ I_OUT ≤ 200 mA, V_OUT = 2.2V
−3
±1.0
+3
%
3.0V ≤ V_BATT = V_IN ≤ 5.5V
V_OUT
Range
Programmable Output Voltage
Range
0 µA ≤ I_OUT ≤ 200 mA
Programming Resolution = 100 mV
1.5
2.8
3.0
V
I_OUT
Output Current
V_IN–V_OUT
ΔV_OUT
Output Current Limit
Dropout Voltage
Line Regulation
e_N
PSRR
Load Regulation
Output Noise Voltage
Power Supply Ripple
Rejection Ratio
(V_OUT + 0.25V, 3.0V)_MAX ≤ V_BATT
V_BATT = V_IN ≤ 5.5V
V_OUT = 0V
I_OUT = 75 mA
(V_OUT + 0.25V, 3.0V)_MAX ≤ V_BATT
V_BATT = V_IN ≤ 5.5V, I_OUT = 75 mA
V_IN = 3.6V, 1 mA ≤ I_OUT ≤ 150 mA
10 Hz ≤ f ≤ 100 kHz,
C_OUT = 2.2 µF
f = 217 Hz, C_OUT = 2.2 µF
150
mA
540
30
174
mV
3
mV
12
41
27
µV_RMS
57
dB
I_GND
Ground Current
I_OUT = 100 µA
C_OUT
Output Capacitance
0 mA ≤ I_OUT ≤ 150 mA
2
Output Capacitor ESR
5
t_START-UP Start-Up Time from Shutdown
C_OUT = 2.2 µF, I_OUT = 150 mA (Note 10)
30
µA
20
µF
500
mΩ
60
µs
V_O3 LDO Electrical Characteristics
Unless otherwise noted, V_IN = V_BATT = 3.6V. Typical values and limits appearing in normal type apply for T_J = 25°C. Limits appearing
in boldface type apply over the entire junction temperature range for operation, −40 to +125°C. (Note 2, Note 8, Note 9)
Symbol
Parameter
Condition
Min
V_OUT
Output Voltage
Accuracy
1 mA ≤ I_OUT ≤ 150 mA, V_OUT = 2.7V
−3
3.0V ≤ V_BATT = V_IN ≤ 5.5V
V_OUT
Range
Programmable Output Voltage
Range
0 µA ≤ I_OUT ≤ 150 mA
Programming Resolution = 100 mV
2.5
I_OUT
Output Current
V_IN–V_OUT
ΔV_OUT
Output Current Limit
Dropout Voltage
Line Regulation
e_N
PSRR
Load Regulation
Output Noise Voltage
Power Supply Ripple
Rejection Ratio
(V_OUT + 0.25V, 3.0V)_MAX ≤ V_BATT
V_BATT = V_IN ≤ 5.5V
V_OUT = 0V
I_OUT = 75 mA
(V_OUT + 0.25V, 3.0V)_MAX ≤ V_BATT
V_BATT = V_IN ≤ 5.5V, I_OUT = 75 mA
V_IN = 3.6V, 1 mA ≤ I_OUT ≤ 150 mA
10 Hz ≤ f ≤ 100 kHz,
C_OUT = 2.2 µF
f = 217 Hz, C_OUT = 2.2 µF
I_GND
Ground Current
I_OUT = 500 µA
C_OUT
Output Capacitance
0 mA ≤ I_OUT ≤ 150 mA
2
Output Capacitor ESR
5
t_START-UP Start-Up Time from Shutdown
C_OUT = 2.2 µF, I_OUT = 150 mA (Note 10)
Typ
±1.0
3.0
520
30
3
12
27
56
30
60
Max
Units
+3
%
3.2
V
150
mA
156
mV
mV
41
µV_RMS
dB
µA
20
µF
500
mΩ
µs
Note: This LDO will be ON after start-up by default. It can be disabled via the register file.
7
200945 Version 4 Revision 2 Print Date/Time: 2011/10/25 13:09:13
www.ti.com