BQ27510-G2 Datasheet, PDF (9/38 Pages) Texas Instruments – System-Side Impedance Track™ Fuel Gauge With Direct Battery Connection

bq27510-G2
www.ti.com
SLUS948 – AUGUST 2010
CNTL FUNCTION
Reserved
PREV_MACWRITE
CHEM_ID
BOARD_OFFSET
SET_HIBERNATE
CLEAR_HIBERNATE
SET_SLEEP+
CLEAR_SLEEP+
SEALED
IT_ENABLE
IF_CHECKSUM
CAL_MODE
RESET
Table 2. Control( ) Subcommands (continued)
CNTL DATA
0x0006
0x0007
0x0008
0x0009
0x0011
0x0012
0x0013
0x0014
0x0020
0x0021
0x0022
0x0040
0x0041
SEALED
ACCESS
No
No
Yes
No
Yes
Yes
Yes
YES
No
No
No
No
No
DESCRIPTION
Not to be used
Returns previous MAC command code
Reports the chemical identifier of the Impedance Track™ configuration
Forces the device to measure and store the board offset
Forces CONTROL_STATUS [HIBERNATE] to 1
Forces CONTROL_STATUS [HIBERNATE] to 0
Forces CONTROL_STATUS [SNOOZE] to 1
Forces CONTROL_STATUS [SNOOZE] to 0
Places the bq27510-G2 in SEALED access mode
Enables the Impedance Track™ algorithm
Reports the instruction flash checksum
Places the bq27510-G2 in calibration mode
Forces a full reset of the bq27510-G2
CONTROL_STATUS: 0x0000
Instructs the fuel gauge to return status information to control addresses 0x00/0x01. The status word includes the
following information.
High Byte
Low Byte
Table 3. CONTROL_STATUS Bit Definitions
bit7
bit6
bit5
bit4
–
FAS
SS
CSV
–
HIBERNATE SNOOZE
SLEEP
bit3
CCA
LDMD
bit2
BCA
RUP_DIS
bit1
–
VOK
bit0
–
QEN
FAS = Status bit indicating the bq27510-G2 is in FULL ACCESS SEALED state. Active when set.
SS = Status bit indicating the bq27510-G2 is in the SEALED State. Active when set.
CSV = Status bit indicating a valid data flash checksum has been generated. Active when set.
CCA = Status bit indicating the bq27510-G2 coulomb counter calibration routine is active. Active when set.
BCA = Status bit indicating the bq27510-G2 board calibration routine is active. Active when set.
HIBERNATE = Status bit indicating a request for entry into HIBERNATE from SLEEP mode. True when set. Default is 0.
SNOOZE = Status bit indicating the bq27510-G2 SLEEP+ mode is enabled. True when set.
SLEEP = Status bit indicating the bq27510-G2 is in SLEEP mode. True when set.
LDMD = Status bit indicating the bq27510-G2 Impedance Track™ algorithm using constant-power mode. True when set. Default is
0 (constant-current mode).
RUP_DIS = Status bit indicating the bq27510-G2 Ra table update status. Updates disabled when set..
VOK = Status bit indicating cell voltages are OK for Qmax updates. True when set.
QEN = Status bit indicating the bq27510-G2 Qmax updates enabled. True when set.
DEVICE_TYPE: 0x0001
Instructs the fuel gauge to return the device type to addresses 0x00/0x01.
FW_VERSION: 0x0002
Instructs the fuel gauge to return the firmware version to addresses 0x00/0x01.
HW_VERSION: 0x0003
Instructs the fuel gauge to return the hardware version to addresses 0x00/0x01.
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
9