5962R8771003VPA Datasheet, PDF (8/30 Pages) Texas Instruments – LM158QML Low Power Dual Operational Amplifiers

LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
www.ti.com
LM158A Electrical Characteristics SMD 5962–8771003 ELDRS Free Only
DC Parameters (continued)
The following conditions apply, unless otherwise specified. All voltages referenced to device ground.
Parameter
Test Conditions
Notes Min Max
I_Sink
I_Source
I_OS
V_IO
CMRR
±I_IB
I_IO
PSRR
V_CM
V_Diff
A_VS
Output Sink Current
Output Source Current
Short Circuit Current
Input Offset Voltage
Common Mode Rejection Ratio
Input BIas Current
+V_CC = 15V, V_O = 200mV,
+V_I = 0V, -V_I = +65mV
+V_CC = 15V, V_O = 2V,
+V_I = 0V, -V_I = +65mV
+V_CC = 15V, V_O = 2V,
+V_I = 0V, -V_I = -65mV
+V_CC = 5V, V_O = 0V
+V_CC = 30V, V_CM = 0V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 30V, V_CM = 28.5V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 30V, V_CM = 28V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 5V, V_CM = 0V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 30V, R_S = 50Ω
V_I = 0V to 28.5V,
+V_CC = 5V, V_CM = 0V
Input Offset Current
+V_CC = 5V, V_CM = 0V
Power Supply Rejection Ratio
Common Mode Voltage Range
+V_CC = 5V to 30V,
V_CM = 0V
+V_CC = 30V
Differential Input Voltage
Large Signal Gain
+V_CC = 15V, R_L = 2KΩ,
V_O = 1V to 11V
12
10
5.0
-20
-10
-60
-2.0 2.0
-4.0 4.0
-2.0 2.0
-4.0 4.0
-2.0 2.0
-4.0 4.0
70
See ⁽¹⁾
See ⁽¹⁾
-50 -1.0
-100 -1.0
-10 10
-30 30
65
See ⁽²⁾, ⁽³⁾
See⁽²⁾, ⁽³⁾
See ⁽⁴⁾
28.5
28.0
32
50
25
Units
µA
mA
mA
mA
mA
mA
mV
mV
mV
mV
mV
mV
dB
nA
nA
nA
nA
dB
V
V
V
V/mV
V/mV
Sub-
groups
1
1
2, 3
1
2, 3
1
1
2, 3
1
2, 3
1
2, 3
1
1
2, 3
1
2, 3
1
1
2, 3
1, 2, 3
4
5, 6
(1) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
(2) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V⁺ −1.5V (at 25°C), but either or both inputs can go to +32V without damage,
independent of the magnitude of V⁺.
(3) Specified by input offset voltage.
(4) Specified parameter not tested.
SMD 5962–8771003 ELDRS Free Only
DC Drift Parameters
The following conditions apply, unless otherwise specified. All voltages referenced to device ground.
Delta calculations are performed on QMLV devices at Group B, Subgroup 5 only.
Parameter
Test Conditions
Notes Min Max
V_IO
Input Offset Voltage
+V_CC = 30V, V_CM = 0V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 30V, V_CM = 28.5V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 5V, V_CM = 0V,
R_S = 50Ω, V_O = 1.4V
-0.5 0.5
-0.5 0.5
-0.5 0.5
Units
mV
mV
mV
Sub-
groups
1
1
1
8
Submit Documentation Feedback
Product Folder Links: LM158QML
Copyright © 2005–2013, Texas Instruments Incorporated