5962R8771003VPA Datasheet, PDF (5/30 Pages) Texas Instruments – LM158QML Low Power Dual Operational Amplifiers

LM158QML
www.ti.com
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
LM158 Electrical Characteristics SMD 5962–8771001 DC Parameters
The following conditions apply, unless otherwise specified. All voltages referenced to device ground.
Parameter
Test Conditions
Notes Min Max
I_CC
V_OH
V_OL
I_Sink
I_Source
I_OS
V_IO
CMRR
±I_IB
I_IO
PSRR
V_CM
V_Diff
A_VS
Power Supply Current
Output Voltage High
Output Voltage Low
Output Sink Current
Output Source Current
Short Circuit Current
Input Offset Voltage
Common Mode Rejection Ratio
Input BIas Current
+V_CC = 5V, R_L = 100K,
V_O = 1.4V
+V_CC = 30V, R_L = 100K,
V_O = 1.4V
+V_CC = 30V, R_L = 2KΩ
+V_CC = 30V, R_L = 10KΩ
+V_CC = 30V, R_L = 10KΩ
+V_CC = 30V, I_Sink = 1µA
+V_CC = 5V, R_L = 10KΩ
+V_CC = 15V, V_O = 200mV,
+V_I = 0V, -V_I = +65mV
+V_CC = 15V, V_O = 2V,
+V_I = 0V, -V_I = +65mV
+V_CC = 15V, V_O = 2V,
+V_I = 0V, -V_I = -65mV
+V_CC = 5V, V_O = 0V
+V_CC = 30V, V_CM = 0V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 30V, V_CM = 28.5V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 30V, V_CM = 28V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 5V, V_CM = 0V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 30V, R_S = 50Ω
V_I = 0V to 28.5V,
+V_CC = 5V, V_CM = 0V
Input Offset Current
+V_CC = 5V, V_CM = 0V
Power Supply Rejection Ratio
Common Mode Voltage Range
+V_CC = 5V to 30V,
V_CM = 0V
+V_CC = 30V
Differential Input Voltage
Large Signal Gain
+V_CC = 15V, R_L = 2KΩ,
V_O = 1V to 11V
1.2
3.0
4.0
26
27
20
20
20
12
10
5.0
-20
-10
-60
-5.0 5.0
-7.0 7.0
-5.0 5.0
-7.0 7.0
-5.0 5.0
-7.0 7.0
70
See ⁽¹⁾
See ⁽¹⁾
-150 -1.0
-300 -1.0
-30 30
-100 100
65
See ⁽²⁾, ⁽³⁾
See⁽²⁾, ⁽³⁾
See ⁽⁴⁾
28.5
28.0
32
50
25
Units
mA
mA
mA
V
V
mV
mV
mV
µA
mA
mA
mA
mA
mA
mV
mV
mV
mV
mV
mV
dB
nA
nA
nA
nA
dB
V
V
V
V/mV
V/mV
Sub-
groups
1, 2, 3
1
2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1
1
2, 3
1
2, 3
1
1
2, 3
1
2, 3
1
2, 3
1
1
2, 3
1
2, 3
1
1
2, 3
1, 2, 3
4
5, 6
(1) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
(2) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V⁺ −1.5V (at 25°C), but either or both inputs can go to +32V without damage,
independent of the magnitude of V⁺.
(3) Specified by input offset voltage.
(4) Specified parameter not tested.
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM158QML
Submit Documentation Feedback
5