5962R8771003VPA Datasheet, PDF (6/30 Pages) Texas Instruments – LM158QML Low Power Dual Operational Amplifiers

LM158QML
SNOSAP3F – JULY 2005 – REVISED MARCH 2013
www.ti.com
LM158A Electrical Characteristics SMD 5962–8771002, High Dose Rate DC Parameters
The following conditions apply, unless otherwise specified. All voltages referenced to device ground.
Parameter
Test Conditions
Notes Min Max Units
Sub-
groups
I_CC
Power Supply Current
+V_CC = 5V, R_L = 100K,
V_O = 1.4V
+V_CC = 30V, R_L = 100K,
V_O = 1.4V
1.2
mA
3.0
mA
4.0
mA
1, 2, 3
1
2, 3
V_OH
Output Voltage High
V_OL
Output Voltage Low
+V_CC = 30V, R_L = 2KΩ
+V_CC = 30V, R_L = 10KΩ
+V_CC = 30V, R_L = 10KΩ
26
V
27
V
40
mV
100
mV
1, 2, 3
1, 2, 3
1
2, 3
+V_CC = 30V, I_Sink = 1µA
40
mV
1
100
mV
2, 3
+V_CC = 5V, R_L = 10KΩ
40
mV
1
100
mV
2, 3
I_Sink
Output Sink Current
+V_CC = 15V, V_O = 200mV,
+V_I = 0V, -V_I = +65mV
+V_CC = 15V, V_O = 2V,
+V_I = 0V, -V_I = +65mV
12
µA
1
10
mA
1
5.0
mA
2, 3
I_Source
Output Source Current
+V_CC = 15V, V_O = 2V,
+V_I = 0V, -V_I = -65mV
-20
mA
1
-10
mA
2, 3
I_OS
Short Circuit Current
V_IO
Input Offset Voltage
+V_CC = 5V, V_O = 0V
+V_CC = 30V, V_CM = 0V,
R_S = 50Ω, V_O = 1.4V
-60
mA
1
-2.0 2.0
mV
1
-4.0 4.0
mV
2, 3
+V_CC = 30V, V_CM = 28.5V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 30V, V_CM = 28V,
R_S = 50Ω, V_O = 1.4V
+V_CC = 5V, V_CM = 0V,
R_S = 50Ω, V_O = 1.4V
-2.0 2.0
mV
1
-4.0 4.0
mV
2, 3
-2.0 2.0
mV
1
-4.0 4.0
mV
2, 3
CMRR
±I_IB
Common Mode Rejection Ratio
Input BIas Current
+V_CC = 30V, R_S = 50Ω
V_I = 0V to 28.5V,
+V_CC = 5V, V_CM = 0V
70
dB
1
See ⁽¹⁾
-50 -1.0
nA
1
See⁽¹⁾ -100 -1.0
nA
2, 3
I_IO
Input Offset Current
+V_CC = 5V, V_CM = 0V
-10 10
nA
1
-30 30
nA
2, 3
PSRR
V_CM
V_Diff
A_VS
Power Supply Rejection Ratio
Common Mode Voltage Range
+V_CC = 5V to 30V,
V_CM = 0V
+V_CC = 30V
Differential Input Voltage
Large Signal Gain
+V_CC = 15V, R_L = 2KΩ,
V_O = 1V to 11V
65
See ^{(2) (3)}
See ^{(2) (3)}
See ⁽⁴⁾
28.5
28.0
32
50
25
dB
V
V
V
V/mV
V/mV
1
1
2, 3
1, 2, 3
4
5, 6
(1) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
(2) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V⁺ −1.5V (at 25°C), but either or both inputs can go to +32V without damage,
independent of the magnitude of V⁺.
(3) Specified by input offset voltage.
(4) Specified parameter not tested.
6
Submit Documentation Feedback
Product Folder Links: LM158QML
Copyright © 2005–2013, Texas Instruments Incorporated