LM3S5762_14 Datasheet, PDF (642/851 Pages) Texas Instruments – Microcontroller

Universal Serial Bus (USB) Controller
Table 16-5. Universal Serial Bus (USB) Controller Register Map (continued)
Offset Name
Type
Reset
Description
See
page
0x130 USBTXMAXP3
R/W
0x0000
USB Maximum Transmit Data Endpoint 3
677
0x132 USBTXCSRL3
R/W
0x00
USB Transmit Control and Status Endpoint 3 Low
687
0x133 USBTXCSRH3
R/W
0x00
USB Transmit Control and Status Endpoint 3 High
691
0x134 USBRXMAXP3
R/W
0x0000
USB Maximum Receive Data Endpoint 3
695
0x136 USBRXCSRL3
R/W
0x00
USB Receive Control and Status Endpoint 3 Low
696
0x137 USBRXCSRH3
R/W
0x00
USB Receive Control and Status Endpoint 3 High
701
0x138 USBRXCOUNT3
RO
0x0000
USB Receive Byte Count Endpoint 3
705
0x13A USBTXTYPE3
R/W
0x00
USB Host Transmit Configure Type Endpoint 3
706
0x13B USBTXINTERVAL3
R/W
0x00
USB Host Transmit Interval Endpoint 3
707
0x13C USBRXTYPE3
R/W
0x00
USB Host Configure Receive Type Endpoint 3
708
0x13D USBRXINTERVAL3
R/W
0x00
USB Host Receive Polling Interval Endpoint 3
709
0x304 USBRQPKTCOUNT1 R/W
0x0000
USB Request Packet Count in Block Transfer Endpoint
1
710
0x308 USBRQPKTCOUNT2 R/W
0x0000
USB Request Packet Count in Block Transfer Endpoint
2
710
0x30C USBRQPKTCOUNT3 R/W
0x0000
USB Request Packet Count in Block Transfer Endpoint
3
710
0x340 USBRXDPKTBUFDIS R/W
0x0000
USB Receive Double Packet Buffer Disable
711
0x342 USBTXDPKTBUFDIS R/W
0x0000
USB Transmit Double Packet Buffer Disable
712
0x400 USBEPC
R/W
0x0000.0000 USB External Power Control
713
0x404 USBEPCRIS
RO
0x0000.0000 USB External Power Control Raw Interrupt Status
716
0x408 USBEPCIM
R/W
0x0000.0000 USB External Power Control Interrupt Mask
717
0x40C USBEPCISC
R/W1C 0x0000.0000 USB External Power Control Interrupt Status and Clear 718
0x410 USBDRRIS
RO
0x0000.0000 USB Device RESUME Raw Interrupt Status
719
0x414 USBDRIM
R/W
0x0000.0000 USB Device RESUME Interrupt Mask
720
0x418 USBDRISC
R/W1C 0x0000.0000 USB Device RESUME Interrupt Status and Clear
721
0x41C USBGPCS
R/W
0x0000.0000 USB General-Purpose Control and Status
722
16.6
OTG B /
Device
Register Descriptions
The LM3S5762 USB controller has On-The-Go (OTG) capabilities as specified in the USB0 bit field
in the DC6 register (see page 216).
This icon indicates that the register is used in OTG B or Device mode. Some registers are used for
both Host and Device mode and may have different bit definitions depending on the mode.
642
July 17, 2014
Texas Instruments-Production Data