TMS320C6748_16 Datasheet, PDF (57/273 Pages) Texas Instruments – Fixed- and Floating-Point DSP

www.ti.com
TMS320C6748
SPRS590F – JUNE 2009 – REVISED MARCH 2014
3.7.23 Universal Parallel Port (uPP)
Table 3-27. Universal Parallel Port (uPP) Terminal Functions
SIGNAL
NAME
VP_CLKIN0 / UHPI_HCS /PRU1_R30[10] / GP6[7] /
UPP_2xTXCLK
PRU0_R30[25] /MMCSD1_DAT[0] / UPP_CHB_CLOCK /
GP8[15]/PRU1_R31[27]
PRU0_R30[24]/ MMCSD1_CLK / UPP_CHB_START / GP8[14] /
PRU1_R31[26]
PRU0_R30[23] / MMCSD1_CMD / UPP_CHB_ENABLE /
GP8[13]/PRU1_R31[25]
PRU0_R30[22] / PRU1_R30[8] / UPP_CHB_WAIT / GP8[12]/
PRU1_R31[24]
PRU0_R30[29] /UHPI_HCNTL0 / UPP_CHA_CLOCK / GP6[11]
PRU0_R30[28] / UHPI_HCNTL1 / UPP_CHA_START / GP6[10]
PRU0_R30[27] / UHPI_HHWIL / UPP_CHA_ENABLE / GP6[9]
PRU0_R30[26] /UHPI_HRW / UPP_CHA_WAIT / GP6[8] /
PRU1_R31[17]
NO.
W14
G1
G2
J4
G3
U17
W15
U16
T15
TYPE ⁽¹⁾
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
PULL ⁽²⁾
CP[25]
CP[30]
CP[30]
CP[30]
CP[30]
CP[24]
CP[24]
CP[24]
CP[24]
POWER
GROUP ⁽³⁾
DESCRIPTION
C
uPP 2x transmit clock input
C
uPP channel B clock
C
uPP channel B start
C
uPP channel B enable
C
uPP channel B wait
C
uPP channel A clock
C
uPP channel A start
C
uPP channel A enable
C
uPP channel A wait
(1) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.
Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name
highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured
function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different
types (ie., input versus output), the table reflects the pin function direction for that particular peripheral.
(2) IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using
the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the
device is out of reset. During reset, all of the pins associated with these registers are pulled down. If the application requires a pull-up,
an external pull-up can be used. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see the Device Configuration section. For electrical specifications on pullup and internal pulldown
circuits, see the Device Operating Conditions section.
(3) This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can
be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of
power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power
supply DVDD3318_C.
Copyright © 2009–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS320C6748
Device Overview
57