LMH6551MAX_NOPB Datasheet, PDF (4/28 Pages) Texas Instruments – LMH6551 Differential, High Speed Op Amp

LMH6551
SNOSAK7C – FEBRUARY 2005 – REVISED MARCH 2013
www.ti.com
±5V Electrical Characteristics ⁽¹⁾ (continued)
Single ended in differential out, T_A= 25°C, G = +1, V_S = ±5V, V_CM = 0V, R_F = R_G = 365Ω, R_L = 500Ω; Unless specified
Boldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min ⁽²⁾ Typ ⁽³⁾ Max ⁽²⁾
Units
V_CM CMRR
Input Resistance
V_ID = 0V, 1V step on V_CM pin, measure
70
75
dB
V_OD
25
kΩ
Common Mode Gain
Output Performance
ΔV_O,CM/ΔV_CM
0.995
0.999
1.005
V/V
Output Voltage Swing
Single Ended, Peak to Peak
±7.38
±7.8
V
±7.18
Output Common Mode Voltage Range V_ID = 0 V,
±3.69
±3.8
V
I_OUT
Linear Output Current
V_OUT = 0V
±50
±65
mA
I_SC
Short Circuit Current
Output Shorted to Ground
V_IN = 3V Single Ended⁽⁷⁾l
140
mA
Output Balance Error
ΔV_OUTCommon Mode
/ΔV_OUTDIfferential , V_OUT = 0.5 Vpp
Differential, f = 10 MHz
−70
dB
Miscellaneous Performance
A_VOL
PSRR
Open Loop Gain
Power Supply Rejection Ratio
Supply Current
Differential
DC, ΔV_S = ±1V
R_L = ∞
70
dB
74
90
dB
11
12.5
14.5
mA
16.5
(7) The maximum output current (I_OUT) is determined by device power dissipation limitations.
5V Electrical Characteristics ⁽¹⁾
Single ended in differential out, T_A= 25°C, G = +1, V_S = 5V, V_CM = 2.5V, R_F = R_G = 365Ω, R_L = 500Ω; Unless
specifiedBoldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min ⁽²⁾ Typ ⁽³⁾ Max ⁽²⁾
Units
SSBW
LSBW
Small Signal −3 dB Bandwidth
Large Signal −3 dB Bandwidth
0.1 dB Bandwidth
Slew Rate
R_L = 500Ω, V_OUT = 0.5 V_PP
R_L = 500Ω, V_OUT = 2 V_PP
V_OUT = 2 V_PP
4V Step⁽⁴⁾
350
300
50
1800
MHz
MHz
MHz
V/μs
Rise/Fall Time, 10% to 90%
4V Step
2
ns
Settling Time
4V Step, 0.05%
17
ns
V_CM Pin AC Performance (Common Mode Feedback Amplifier)
Common Mode Small Signal
Bandwidth
170
MHz
Distortion and Noise Response
HD2
2^nd Harmonic Distortion
HD2
HD3
3^rd Harmonic Distortion
HD3
e_n
Input Referred Noise Voltage
i_n
Input Referred Noise Current
V_O = 2 V_PP, f = 5 MHz, R_L=800Ω
V_O = 2 V_PP, f = 20 MHz, R_L=800Ω
V_O = 2 V_PP, f = 5 MHz, R_L=800Ω
V_O = 2 V_PP, f = 20 MHz, R_L=800Ω
Freq ≥ 1 MHz
Freq ≥ 1 MHz
−84
dBc
−69
dBc
−93
dBc
−67
dBc
6.0
nV/√Hz
1.5
pA/√Hz
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that T_J = T_A. No specification of parametric performance is indicated in the electrical tables under
conditions of internal self-heating where T_J > T_A.
(2) Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control (SQC) methods.
(3) Typical numbers are the most likely parametric norm.
(4) Slew Rate is the average of the rising and falling edges.
4
Submit Documentation Feedback
Product Folder Links: LMH6551
Copyright © 2005–2013, Texas Instruments Incorporated