|
OPA3692IDBQT Datasheet, PDF (3/26 Pages) Texas Instruments – Triple, Wideband, Fixed Gain Video BUFFER AMPLIFIER With Disable | |||
|
◁ |
ELECTRICAL CHARACTERISTICS: VS = ±5V (Cont.)
Boldface limits are tested at +25°C.
G = +2 (âIN grounded) and RL = 100⦠(see Figure 1 for AC performance only), unless otherwise noted.
OPA3692ID, OPA3692IDBQ
PARAMETER
CONDITIONS
TYP
+25°C
MIN/MAX OVER TEMPERATURE(1)
+25°C
0°C to â40°C to
MIN/ TEST
70°C
+85°C UNITS MAX LEVEL(2 )
AC PERFORMANCE (Cont.)
Settling Time to 0.02%
0.1%
Harmonic Distortion
2nd-Harmonic
3rd-Harmonic
Input Voltage Noise
Noninverting Input Current Noise
Inverting Input Current Noise (Internal)
Differential Gain
Differential Phase
Channel-to-Channel Crosstalk
G = +2, VO = 2V Step
12
ns
typ
C
G = +2, VO = 2V Step
8
ns
typ
C
G = +2, f = 5MHz, VO = 2VPP
RL = 100â¦
â69
â62
â59
â57
dBc
max
B
RL ⥠500â¦
â79
â70
â67
â65
dBc
max
B
RL = 100â¦
â76
â72
â70
â68
dBc
max
B
RL ⥠500â¦
â94
â87
â82
â78
dBc
max
B
f > 1MHz
1.7
2.5
2.9
3.1
nV/âHz max
B
f > 1MHz
12
14
15
15
pA/âHz max
B
f > 1MHz
15
17
18
19
pA/âHz max
B
NTSC, RL = 150â¦
NTSC, RL = 37.5â¦
NTSC, RL = 150â¦
NTSC, RL = 37.5â¦
0.07
0.17
0.02
0.07
%
typ
C
%
typ
C
deg
typ
C
deg
typ
C
f = 5MHz, Input Referred, All Hostile â82
dBc
typ
C
DC PERFORMANCE(3)
Gain Error
Internal RF and RG
Maximum
Minimum
Average Drift
Input Offset Voltage
Average Offset Voltage Drift
Noninverting Input Bias Current
Average Noninverting Input Bias Current Drift
Inverting Input Bias Current
Average Inverting Input Bias Current Drift
INPUT
Common-Mode Input Range
Noninverting Input Impedance
G = +1
G = +2
G = â1
VCM = 0V
VCM = 0V
VCM = 0V
VCM = 0V
VCM = 0V
VCM = 0V
±0.2
±0.3
±1.5
±0.2
±1.5
402
457
402
347
0.13
±0.8
±3
+15
+35
±5
±25
±3.5
±3.4
100 || 2
±1.6
±1.6
462
342
0.13
±3.7
±12
+43
â300
±30
±90
±3.3
%
typ
C
±1.7
%
max A
±1.7
%
max B
464
â¦
max A
340
â¦
min
A
0.13
%/°C max
B
±4.3
mV
max
A
±20
µV/°C max
B
+45
µA
max
A
â300
nA/°C max
B
±40
µA
max
A
±200
nA°C max
B
±3.2
V
min
B
k⦠|| pF typ
C
OUTPUT
Voltage Output Swing
Current Output, Sourcing
Sinking
Short-Circuit Current
Closed-Loop Output Impedance
No Load
100⦠Load
G = +2, f = 100kHz
±4.0
±3.9
+190
â190
±250
0.12
±3.8
±3.7
+160
â160
±3.7
±3.6
+140
â140
±3.6
±3.3
+100
â100
V
min
A
V
min
A
mA
min
A
mA
min
A
mA
typ
C
â¦
typ
C
DISABLE/POWER DOWN (DIS Pin)
Power-Down Supply Current (+VS)
Disable Time
Enable Time
Off Isolation
Output Capacitance in Disable
Turn-On Glitch
Turn-Off Glitch
Enable Voltage
Disable Voltage
Control Pin Input Bias Current
POWER SUPPLY
Specified Operating Voltage
Maximum Operating Voltage Range
Maximum Quiescent Current (3 Channels)
Minimum Quiescent Current (3 Channels)
Power-Supply Rejection Ratio (âPSRR)
VDIS = 0, All Channels
VIN = +1VDC
VIN = +1VDC
G = +2, 5MHz
G = +2, RL = 150â¦, VIN = 0V
G = +2, RL = 150â¦, VIN = 0V
VDIS = 0, Each Channel
VS = ±5V
VS = ±5V
Input Referred
â450
1
25
74
4
±50
±20
3.3
1.8
75
±5
15.3
15.3
58
â900
â1050 â1200
3.5
3.6
3.7
1.7
1.6
1.5
130
150
160
±6
±6
±6
15.9
16.8
17.4
14.7
13.2
12.75
52
50
49
µA
max A
µs
typ
C
ns
typ
C
dB
typ
C
pF
typ
C
mV
typ
C
mV
typ
C
V
min
A
V
max A
µA
max
A
V
typ
C
V
max
A
mA
max
A
mA
min
A
dB
min
A
TEMPERATURE RANGE
Specification: D, DBQ
Thermal Resistance, θJA
D
SO-16
DBQ SSOP-16
â40 to +85
100
100
°C
typ
C
°C/W
typ
C
°C/W
typ
C
NOTES: (1) Junction temperature = ambient temperature for low temperature limit and +25°C specifications. Junction temperature = ambient temperature +15°C at
high temperature limit specifications. (2) Test Levels: (A) 100% tested at +25°C. Over-temperature limits by characterization and simulation. (B) Limits set by
characterization and simulation. (C) Typical value only for information. (3) Current is considered positive out-of-node. VCM is the input common-mode voltage.
OPA3692
3
SBOS228E
www.ti.com
|
▷ |