DS90LV001_14 Datasheet, PDF (3/22 Pages) Texas Instruments – 800 Mbps LVDS Buffer

DS90LV001
www.ti.com
SNLS067E – JANUARY 2001 – REVISED APRIL 2013
Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified⁽¹⁾⁽²⁾
Symbol
Parameter
Conditions
Min Typ Max Units
LVCMOS/LVTTL DC SPECIFICATIONS (EN)
V_IH
High Level Input Voltage
V_IL
Low Level Input Voltage
I_IH
High Level Input Current
I_IL
Low Level Input Current
V_CL
Input Clamp Voltage
LVDS OUTPUT DC SPECIFICATIONS (OUT)
V_IN = 3.6V or 2.0V, V_CC = 3.6V
V_IN = GND or 0.8V, V_CC = 3.6V
I_CL = −18 mA
2.0
GND
V_CC
V
0.8
V
+7 +20 μA
±1 ±10 μA
−0.6 −1.5 V
V_OD
ΔV_OD
Differential Output Voltage
Change in Magnitude of V_OD for Complimentary
Output States
R_L = 100Ω
Figure 2 and Figure 3
250 325 450 mV
20
mV
V_OS
ΔV_OS
Offset Voltage
Change in Magnitude of V_OS for Complimentary
Output States
R_L = 100Ω
Figure 2
1.080 1.19 1.375 V
20
mV
I_OZ
Output TRI-STATE Current
I_OFF
Power-Off Leakage Current
I_OS
Output Short Circuit Current⁽³⁾
I_OSD
Differential Output Short Circuit Current⁽³⁾
LVDS RECEIVER DC SPECIFICATIONS (IN)
EN = 0V, V_OUT = V_CC or GND
V_CC = 0V, V_OUT = 3.6V or GND
EN = V_CC, V_OUT+ and V_OUT− = 0V
EN = V_CC, V_OD = 0V
±1 ±10 μA
±1 ±10 μA
−16 −24 mA
−7 −12 mA
V_TH
V_TL
V_CMR
I_IN
Differential Input High Threshold
Differential Input Low Threshold
Common Mode Voltage Range
Input Current
ΔI_IN
Change in Magnitude of I_IN
SUPPLY CURRENT
V_CM = +0.05V, +1.2V or +3.25V
V_ID = 100mV, V_CC = 3.3V
V_IN = +3.0V
V_CC = 3.6V or 0V
V_IN = 0V
V_IN = +3.0V
V_CC = 3.6V or 0V
V_IN = 0V
0 +100 mV
−100 0
mV
0.05
3.25 V
±1 ±10 μA
±1 ±10 μA
1
6
μA
1
6
μA
I_CCD
Total Supply Current
I_CCZ
TRI-STATE Supply Current
EN = V_CC, R_L = 100Ω, C_L = 5 pF
EN = 0V
47
70
mA
22
35
mA
(1) Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground
except V_OD and ΔV_OD.
(2) All typical are given for V_CC = +3.3V and T_A = +25°C, unless otherwise stated.
(3) Output short circuit current (I_OS) is specified as magnitude only, minus sign indicates direction only.
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: DS90LV001
Submit Documentation Feedback
3