DAC904 Datasheet, PDF (3/23 Pages) Burr-Brown (TI) – 14-Bit, 165MSPS DIGITAL-TO-ANALOG CONVERTER

ELECTRICAL CHARACTERISTICS (Cont.)
At T_A = +25°C, +V_A = +5V, +V_D = +5V, differential transformer coupled output, 50Ω doubly terminated, unless otherwise specified.
DAC904U, E
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
DYNAMIC PERFORMANCE (Cont.)
Output Settling Time⁽²⁾
Output Rise Time⁽²⁾
Output Fall Time⁽²⁾
Glitch Impulse
DC-ACCURACY
Full-Scale Output Range⁽³⁾(FSR)
Output Compliance Range
Gain Error
Gain Error
Gain Drift
Offset Error
Offset Drift
Power-Supply Rejection, +V_A
Power-Supply Rejection, +V_D
Output Noise
Output Resistance
Output Capacitance
REFERENCE
Reference Voltage
Reference Tolerance
Reference Voltage Drift
Reference Output Current
Reference Input Resistance
Reference Input Compliance Range
Reference Small-Signal Bandwidth⁽⁴⁾
DIGITAL INPUTS
Logic Coding
Latch Command
Logic HIGH Voltage, V_IH
Logic LOW Voltage, V_IL
Logic HIGH Voltage, V_IH
Logic LOW Voltage, V_IL
Logic HIGH Current^, I_IH(5)
Logic LOW Current, I_IL
Input Capacitance
POWER SUPPLY
Supply Voltages
+V_A
+V_D
Supply Current⁽⁶⁾
I_VA
I_VA, Power-Down Mode
I_VD
Power Dissipation
Power Dissipation, Power-Down Mode
Thermal Resistance, θ_JA
SO-28
TSSOP-28
to 0.1%
10% to 90%
10% to 90%
All Bits HIGH, I_OUT
With Internal Reference
With External Reference
With Internal Reference
With Internal Reference
With Internal Reference
I_OUT = 20mA, R_LOAD = 50Ω
I_OUT, I_OUT to Ground
+V_D = +5V
+V_D = +5V
+V_D = +3V
+V_D = +3V
+V_D = +5V
+V_D = +5V
+5V, I_OUT = 20mA
+3V, I_OUT = 2mA
30
2
2
3
2.0
–1.0
–10
–10
–0.025
–0.2
–0.025
±1
±2
±120
±0.1
50
200
12
20.0
+1.25
+10
+10
+0.025
+0.2
+0.025
+1.24
±10
±50
10
1
0.1
1.25
1.3
Straight Binary
Rising Edge of Clock
3.5
5
0
1.2
2
3
0
0.8
±20
±20
5
ns
ns
ns
pV-s
mA
V
%FSR
%FSR
ppmFSR/°C
%FSR
ppmFSR/°C
%FSR/V
%FSR/V
pA/√Hz
kΩ
pF
V
%
ppmFSR/°C
µA
MΩ
V
MHz
V
V
V
V
µA
µA
pF
+2.7
+5
+5.5
V
+2.7
+5
+5.5
V
24
30
mA
1.1
2
mA
8
15
mA
170
230
mW
50
mW
45
mW
75
°C/W
50
°C/W
NOTES: (1) At output I_OUT, while driving a virtual ground. (2) Measured single-ended into 50Ω Load. (3) Nominal full-scale output current is 32x I_REF; see Application
Section for details. (4) Reference bandwidth depends on size of external capacitor at the BW pin and signal level. (5) Typically 45µA for the PD pin, which has an
internal pull-down resistor. (6) Measured at f_CLOCK = 50MSPS and f_OUT = 1.0MHz.
DAC904
3
SBAS095C
www.ti.com